Ask Experts Questions for FREE Help !
Ask
    meh428's Avatar
    meh428 Posts: 3, Reputation: 1
    New Member
     
    #1

    Nov 21, 2009, 05:57 PM
    Installing a One-Piece Seamless Tub Surround. How much I should I charge?
    I'm installing a One-Piece Seamless Tub Surround. How much I should I charge? I don't have to do any plumbing work. Just installation.

    Charge by the hour?
    Or
    For the job?
    BuilderBrent's Avatar
    BuilderBrent Posts: 8, Reputation: 4
    New Member
     
    #2

    Nov 22, 2009, 12:59 PM
    Yes, the ever important question.

    From a builders perspective. Charging for time and materials (hourly plus cost of materials used) is much safer for you. You won't run the risk of not making enough money for your time and you won't end up paying for unexpected materials.

    The problem with "time and materials" comes into play if you you end up taking too long to complete it, thus turning a $300 project into an $800 project and making someone very upset. Also, many homeowners are very skeptical about paying someone hourly, especially if the person doing the work is not a professional.

    What I have done in the past for small projects like this, is written a contract for time and materials but placed a maximum cost that I would not go over. (It's basically a bid except that if you complete it for less, then they pay less.) This way you are protected as long as you take a reasonable amount of time, and your customer is protected if you completely overlooked something or bit off more than you can chew. (which is your responsibility anyway.)

    I have signed many smaller projects this way. Its good way to build trust, and as long as you know what your doing there should never be an issue.

    Sorry, I forgot to answer your first question.

    How much? Unfortunately, you are the only person who can answer that. I have given a few up and coming builders this advice. "Charge what you need to charge, not what you need to charge to get the job." Don't sell yourself short. If you think you are worth twenty dollars an hour, then that is what you charge. Or if you are doing this as a side job, put a value on what you would have been doing had you not taken the job and then charge accordingly.

    hope this helps.
    mtconc's Avatar
    mtconc Posts: 119, Reputation: 9
    Junior Member
     
    #3

    Nov 22, 2009, 08:59 PM

    I agree.. that's a good idea to help both parties
    pattyg2's Avatar
    pattyg2 Posts: 480, Reputation: 27
    Full Member
     
    #4

    Dec 6, 2009, 05:32 PM

    The first thing you need to do is find out if the one piece surround will fit through the bathroom door.
    I had to cut mine up into pieces to get it out of the bathroom since the installed it before walls were done and door installed.
    cyberheater's Avatar
    cyberheater Posts: 321, Reputation: 12
    Full Member
     
    #5

    Dec 7, 2009, 09:12 AM

    All above is good advice.

    Some issues to consider for your install: Do you have rough frame in, or is the walls completely finished?

    The walls will never be exact in plumb if someone else did this. Count on using shims and other materials. It is not as easy just to think you can just slide it in there without having to make adjustments. I wish it were, but I know it's not from doing it.

    Also look at the manufacturer's installation instructions, and the area you are installing to ensure you are prepared for any problems. Then you can have an idea of how long this will take you and give a better rate/bid. Make sure the plumbing is ready for you to place that piece in. Can't tell you how many times this has happened. A job not being ready for you to do yours. You may need two people, and if you have to slide this piece over the rough in plumbing, it can be tricky.
    Milo Dolezal's Avatar
    Milo Dolezal Posts: 7,192, Reputation: 523
    Plumbing Expert
     
    #6

    Dec 7, 2009, 06:57 PM

    One Piece Tub with Surround is installed in new houses during the framing stages. Good question was raised above: How the heck do you plan on getting it in now ?

    Lasco sells same concept tub with surround but the surround and tub are two separate pieces.

    As far as charges go: without any plumbing required - just putting it in, setting it in mortar, leveling it and attaching it to the walls - you and your helper should be done in 30 minutes. So figure what you want to make...

    Plumbing is what makes this work more expensive. Without plumbing labor charges are your call...

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Corner gaps in one piece tub surround [ 1 Answers ]

I bought a one piece tub surround from Lowe's. It did not come with anything to put in the corners. When you push the surround into the corners there is still gap at the top. Where can I get corner caps to fill the gap or what is the best way to install?

Tub surround-3 piece install [ 4 Answers ]

I purchased a 3 piece tub/shower surround and replaced the walls with green board,patched all the seams and corners with drywall mud,sanded and ready to install 3 piece unit. Installed first wall opposite fixture wall,drew level line all around the top of the rest of the walls.drilled holes for...

How do I remove a one piece bathtub/surround [ 1 Answers ]

How do I remove a one piece bathtub/surround

Trying to find a one piece tub surround to fit a large jet tub [ 1 Answers ]

I recently purchased a home with a large juccuzzi jet tub (measures 73" long, 36" deep, and I can go as high as 78" to my ceiling) . I would like to put in a new tub surround, however, I have talked with rona, home depot, and many renovators in my area and they all are telling me that I can not...

Preparation to install a 5 piece tub surround [ 1 Answers ]

What is the best way to intall a tub surround? The green board is already up and primer. There are no instruction to be found. What preparations do I have to do first? Do I have to use mineral sprits on the backing before I apply the adhesive?


View more questions Search