Ask Experts Questions for FREE Help !
Ask
    joefam's Avatar
    joefam Posts: 2, Reputation: 1
    New Member
     
    #1

    Nov 28, 2009, 04:39 PM
    Copper plumbing compression fittings
    How do I reconnect 1/2"opper tubing that has been cut?
    hkstroud's Avatar
    hkstroud Posts: 11,929, Reputation: 899
    Home Improvement & Construction Expert
     
    #2

    Nov 28, 2009, 04:43 PM

    Well, you could solder with a coupling. If it is not concealed you could reconnect with a compression coupling or a Sharkbite coupling.

    You posted twice, delete other post.
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #3

    Nov 28, 2009, 05:27 PM
    Hi all...

    Just wanted to provide a visual for Joefam...

    Like Harold said, if concealed plumbing (wall will cover) then you are best to solder the piping using some copper couplings. If the pipes are exposed then you can use 5/8" O.D. compression couplings or use 1/2" copper sharkbite or gatorbite fittings.

    The sharkbite or gatorbite fittings (see images below) are easiest in that they are simple PUSH FIT type fittings. Here, you must have a clean cut on the copper pipe and then you simply push the coupling (or any type fitting) onto the pipe to the proper depth.

    You will probably need to purchase a small piece of 1/2" copper pipe (TYPE L for drinking water) and 1/2" sharkbite coupling(s). Also, not a bad idea to purchase a tubing cutter (see last image) to make the cuts nice and smooth.

    Let us know if you want to discuss more here...

    MARK
    Attached Images
       
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #4

    Nov 28, 2009, 06:06 PM

    You guys forgot the most important part. There is the REPAIR COUPLING and a COUPLING. Only the repair coupling will work because the tube won't stop in the middle due to a dimple or score.

    You can cut the tube in half. Prepare the ends and slip a repair coupling on one side. Put the pipe together and center the repair coupling over the seam. Solder.
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #5

    Nov 28, 2009, 06:17 PM
    Good point KISS. If Joe only has a single cut that needs to be repaired he can just finish the cut in the pipe, clean all this up and install a repair coupling and solder this all up as you mentioned.

    If he has to span a small distance due to damage to the pipe he can use a regular coupling and then span the distance with copper tubing and connect all up using that repair coupling you mentioned. Certainly makes things easier if there is no room to move the pipes!

    Otherwise, if there is room to move the pipes... sharkbite or gatorbite fitting is still best solution if Joe doesn't have all the soldering tools!

    Thanks..


    MARK
    topcat6's Avatar
    topcat6 Posts: 40, Reputation: 2
    Junior Member
     
    #6

    Nov 28, 2009, 10:24 PM

    At the price of those sharkebit or compression fittings or how long they hold up compared to sweated fittings! Learn how to sweat and buy the torch!

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Best way to cap a copper water line: compression fitting or copper cap? [ 29 Answers ]

Hi all, Unsuccessfully tried to cap a copper water line by soldering a pre-soldered cap onto the end. Took all the proper steps, cleaned the ends of the pipe and fitting first, then applied flux around both. Wasn't quite sure what I should be heating, so I just heated everything. After my first...

Copper plumbing compression fittings [ 1 Answers ]

How do I connect !/2" copper pipe (straight line) that has been cut? With compresssion fittings?

Compression fittings not in far enough [ 1 Answers ]

I just fixed my old dishwasher line and I had to cut out a leak. I had enough copper tubing to just reroute the remaining tubing into the valve stop. However, it is an older house and the outside diameter of the tubing was a bit wider than what we use now. I got the nut on as far as I could and...

Pre-soldered copper fittings! [ 3 Answers ]

What's new! Can anyone tell me how this new pre-soldered fittings can work. Would pro's use them? Thanks


View more questions Search