Ask Experts Questions for FREE Help !
Ask
    karlomtz's Avatar
    karlomtz Posts: 14, Reputation: 0
    New Member
    		  
    #1

    Oct 31, 2009, 11:04 AM
    Furnace Problems
    Ok, I got all my answers here during Summer on fixing my AC myself but now Winter is coming and my furnace is not working, AC works great but not the heat.

    - system is Gas not Electric
    - turned the TS to Auto and Heat but nothing only hear a click
    - put it in ON and Heat and the blower turns on, I went to take a look at it and waited a few minutes but only the blower is working no flame
    - checked all wiring and everything looks good

    During summer when I was fixing my AC I replace the blower, trans, board and TS so they are all new about 6 months old.

    Board:
    Honeywell
    Model - ST9141 A 1002
    Part # - 406650

    Led light gives 3 Flash: Pressure Switch-NC Circuit Open


    TS:
    White-Rodgers - 1F78H
    Non-Programmable Thermostat


    Please let me know if you have any suggestions or if you need some more information.

    Thanks
    T-Top's Avatar
    T-Top Posts: 1,871, Reputation: 100
    Ultra Member
    		  
    #2

    Oct 31, 2009, 08:10 PM
    Sounds like you have a stuck pressure switch or its wired wrong.
    karlomtz's Avatar
    karlomtz Posts: 14, Reputation: 0
    New Member
    		  
    #3

    Oct 31, 2009, 09:31 PM

    Thanks, I'll check that next
    karlomtz's Avatar
    karlomtz Posts: 14, Reputation: 0
    New Member
    		  
    #4

    Dec 2, 2009, 06:16 PM

    Forgot all about it after the weather got better but now the cold is coming and have not called anyone to look at it and will need it now to work.

    So any other suggestions would help before I call someone.

    Thank you
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #5

    Dec 2, 2009, 07:28 PM
    Just check as mentioned before.

    Led light gives 3 Flash: Pressure Switch-NC Circuit Open

    Check pressure switch for proper operation.

    Check pressure switch hose to be sure it contains no water and has no holes or cracks.
    KC13's Avatar
    KC13 Posts: 2,556, Reputation: 99
    Ultra Member
    		  
    #6

    Dec 2, 2009, 09:35 PM

    Try removing the flue pipe from the inducer outlet, and BRIEFLY run the furnace. If it operates normally, the flue/chimney is blocked.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Thermostat problems or furnace problems [ 22 Answers ]

Is it possible that a thermostat operates correct all the time except when it reaches the temperature that is set doesn't maintain that temperature?:D I noticed that actually that thermostat gives a signal to the furnace but furnace doesn't turn on but that happens only when thermostat needs to...

Furnace problems [ 2 Answers ]

My furnace won't come on. I have electric heat, and when I set the heat it does nothing,can someone help me?

Furnace problems [ 1 Answers ]

I have an Intertherm gas furnace and the draft inducer stays running after the furnace cuts out. Any Ideas Why?

Furnace problems [ 2 Answers ]

I have a goodman central heating system model capf036a2a. The problem I'm having is when it turns on the flame will ignite and after about five seconds it will turn off. It will keep doing this over and over eventually it will stay on for a few days but it keeps doing this.

Furnace problems [ 5 Answers ]

My unit is about 9yrs old. It's an Evcon/Coleman... The problem is that when you set the temp. it will kick on but there is no fire through the little window. It will not light at all. Could something need cleaned or adjusted and if so how do I go about doing it. I am somewhat mechanically...

View more questions Search