Ask Experts Questions for FREE Help !
Ask
    mikenrickd's Avatar
    mikenrickd Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Oct 7, 2009, 03:55 AM
    Gmp100-3 furnace seems dead
    I am trying to find out why a gmp100-3 furnace does nothing. I have not yet tried anything except open covers. The control board has not led on, does this mean it is shot or could there be another problem. Any answers to this problem would be great. (live in cleveland, getting cold :) at night)
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #2

    Oct 7, 2009, 04:32 AM
    First make sure the power is turned on to the furnace and the thermostat is calling for heat.

    Next check the blower safety switch since when the panel is off the furnace will not work anyway. This little switch does go bad so I suggest you test it to make sure it is good before going further.

    If your unit has a circuit board there should be a fuse on it so check that after you test the blower door switch. Post back with results.
    mikenrickd's Avatar
    mikenrickd Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Oct 20, 2009, 05:26 PM

    I have power to the switch, from the switch and to the circuit board. The led (red) still not on. Fuse is good, even replaced it.Connected therm wires red/white together,still nothing. I called repair service, and they want $100-00 just to look at it, price includes first half hour. Another place said furnace being in attic may incure a $75.00 extra fee. Seems like a ripoff.
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #4

    Oct 20, 2009, 05:32 PM
    If you have power to the board (110/120)Volts and the light is not on with all the other stuff you checked I would say it has to be the board.
    lil joe's Avatar
    lil joe Posts: 12, Reputation: 1
    New Member
    		  
    #5

    Oct 20, 2009, 05:40 PM
    Quote Originally Posted by hvac1000 View Post
    If you have power to the board (110/120)Volts and the light is not on with all the other stuff you checked I would say it has to be the board.
    Should there not be 24v to the board? Might it be a bad transformer?
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Goodman GMP100-3 Furnace won't Stay On. [ 14 Answers ]

Hello, I have a Goodman Furnace (model # GMP100-3). The furnace will not stay running. Here is the sequence of events for two different scenarios that are occurring. Scenario 1 1. Thermostat Calls for Heat 2. Inducer starts 3. Pressure switch closes 4. Heating element glows 5. Burners...

York furnace gmp100-3 [ 2 Answers ]

My furnace won't stay running. The inducer motor kicks on but then shuts off. The control board light flashes 3 times telling me the pressure switch failed to close. I cleaned the hose and replaced the pressure switch since it was about 13-14 y/o. I also cleaned the opening to the inducer motor....

Need definitions for dead against /dead mens shoes/ dead marines [ 2 Answers ]

I need help with the definitions of dead against /dead mens shoes/ dead marines for socioloy class . Please help

Wiring inline duct fan to furnace fan goodman gmp100-4 [ 2 Answers ]

How do I wire my inline duct fan to my Goodman model gmp100-4 gas furnace fan so that the inline duct fan comes on and off when the furnace fan does? I understand that I need a relay from the inline duct fan but don't know where to connect the relay to the furnace.

Heating Capacity of a GMP100-4 FURNACE [ 3 Answers ]

Hi. I am a new member and I want to be as specific as possible so I can get the correct answer. I have a GMP100-4 furnace working properly in my house. I need to know the heating capacity of this machine because I want to add a AC Coil so I can use a Condensing Units that I received as a gift...

View more questions Search