 |
|
|
 |
New Member
|
|
Sep 14, 2009, 10:10 AM
|
|
Keyboard light flashing
I have a p4 computer with u8668-d mother board.
There is no display,the key board lights are flashing together,and cpu fans are running,no light on power led.
How can I solve it? Is my mother board OK and the processor?
|
|
 |
Ultra Member
|
|
Sep 14, 2009, 10:58 AM
|
|
Any changes that either happened or that you perhaps made to your computer around the time that the problem started; particularly any Software or Hardware that you installed or setup.
Has the computer been moved?
Try unplugging all connections from computer and then reseat or put back all connections and try again
Also, try to unplug the computer while turned off and plug back in
|
|
 |
New Member
|
|
Sep 16, 2009, 05:08 AM
|
|
I have tried unplugging all the cabels and re joining them,still the problem continues,
|
|
 |
Ultra Member
|
|
Sep 16, 2009, 08:31 AM
|
|
Do you have access to another monitor you can try and use on this? If so, connect another monitor just to see if the monitor is possible problem
|
|
 |
New Member
|
|
Sep 16, 2009, 10:27 AM
|
|
Yes I have tried joining another moniter,but the problem still continues,my monitor works well with anpther cpu. Any other idea?
Please help me
|
|
 |
Ultra Member
|
|
Sep 16, 2009, 10:29 AM
|
|
Was the computer moved recently?
|
|
 |
New Member
|
|
Sep 16, 2009, 10:34 AM
|
|
No it was not moved but I unplugged every thing and cleaned it with smooth brush,and plugged it again.it had a dislpay,I entered into BIOS and it hanged.so I pushed restart button,
And the display has gone.
|
|
 |
Ultra Member
|
|
Sep 16, 2009, 10:56 AM
|
|
Do you have a any disc that is bootable?
If you do, start the computer with the bootable disk to see if it will boot to the disk and not the operating system without issue.
|
|
 |
New Member
|
|
Sep 16, 2009, 11:01 AM
|
|
Yes I have tried it,no result,as there is no display,but I can hear hard disk clinking with small sound,my cd drive,ram hard disk are working well.I have tested them in another computer
|
|
 |
Ultra Member
|
|
Sep 16, 2009, 11:10 AM
|
|
One of the last things to consider other than the system board itself would be your video card.
By chance, would you have access to another video card that you can swap out with the one you have in the computer now?
If so, changing the video card to a known working video card would narrow down to the video card itself or something with the system board.
But if everything seems to be working as you have mentioned but just no display and you have tested on another monitor and your monitor does work on another computer, this leaves the video card itself as the culprit
|
|
 |
New Member
|
|
Sep 24, 2009, 04:49 AM
|
|
Nothing worked,thaks 4 all your help
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Flashing power light
[ 5 Answers ]
My computer power light is flashing on an off. Computer won't switch on. Any advice would be great.
Flashing red light code ?
[ 10 Answers ]
OK I have seen the same question asked and followed the instructions, BUT I can't find the meaning of my code on the inside of my access panel.
I have a Trane XE80 with a White-Rodgers 50a50-473 control panel, the heat cycles on and off every 20 30min. The flashing code is (I think) 14 ...
Flashing oil light
[ 1 Answers ]
92 Honda accord lx, well maintained oil change and filter, oil level good, whay is oil light now flashing?
Flashing status light
[ 3 Answers ]
I have a York Diamond 90 furnace. When I turned it on for the winter, it starts but only runs for a minute and then shuts off but the blower still runs. When I checked the status light it blinks four times which according to the panel indicates "High Aux or Spill Limit Switch Open"
I am handy...
View more questions
Search
|