 |
|
|
 |
Full Member
|
|
Jul 19, 2009, 11:56 AM
|
|
Installing draywall over existing wall
There is paneling in my kitchen from the previous owner. I wanted to paint the wall so I removed a section of the paneling and the wall beneath is wallpapered and is in pretty bad condition so I wanted to start fresh with new drywall. I was thinking of installing a .25 inch layer of drywall over the existing wall. Excluding the fact that I's be losing a quarter inch of space around the room, are there any other cons against doing this? Would I be better off removing the old drywall and starting fresh?
|
|
 |
Home Improvement & Construction Expert
|
|
Jul 19, 2009, 12:44 PM
|
|
May need to add 1/4 spacer to door and window facing and put 1/4" extensions on electrical outlets and switches.
|
|
 |
Full Member
|
|
Jul 19, 2009, 02:15 PM
|
|
Thanks. I guess the only other question I have is does it negatively affect the value of your home to hang drywall over existing wall?
|
|
 |
Home Repair & Remodeling Expert
|
|
Jul 19, 2009, 03:12 PM
|
|
Yes it would be a draw back to some buyers. They will see it as a DYI lazy repair. They will wonder and be turned off by not knowing what you were hiding. If the old drywall is truly beyond repair the tear it out. Have you tried to remove and of the paper?
|
|
 |
Junior Member
|
|
Jul 19, 2009, 03:42 PM
|
|
Definitely demo the old paneling. This way you will be able to easily locate the studs and line the drywall up appropriately to the studs... which is of the utmost importance when hanging drywall... also use 1/2 inch drywall. If I was looking to buy a house and knew that drywall had been installed over paneling, I would definitely wonder about the other "home improvements" that had been done to the house. Paneling is relatively easy to demo.
|
|
 |
Full Member
|
|
Jul 19, 2009, 04:11 PM
|
|
Yea I think I was leaning toward taking it out anyway. I haven't tired to remove any of the paper but it doesn't look like it will come off that easy. Also, I've removed wall paper before and I know how much of a pain that is, so I am probably just going to remove that old wall all together. I was only going to use the .25 inch if I installed over the old wall, I'll definitely use the half inch. Thanks for your input.
|
|
 |
Home Repair & Remodeling Expert
|
|
Jul 20, 2009, 07:57 AM
|
|
I would think it worth your while to test a small area for wall paper removal. Yes, it is a pain but removing the old drywall and new installation is no snap either, especially if you are great at mudding.
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Installing wall tiles over top existing wall tiles
[ 2 Answers ]
I am renovating a bathroom and want to change the tiles in the shower. I was wondering if I could install the new tiles overtop the existing tiles to avoid destroying the wall and what steps to follow if this can be done. The existing tile is in great shape but not the desired colour.
Installing a heat duct in existing basement wall
[ 3 Answers ]
I need tips to install a 6x10 heat duct in a wall. I have installed a wood burner and want to vent one of the heat runs into a large family room. The family room side is finished, the back of the wall is in my mechanical room and unfinished.
Installing wall tiles over existing tile
[ 5 Answers ]
We have a fireplace with some old tiles, which we'd like to replace. Question is, can we just install over the existing tiles, or must we remove the existing tiles?
Installing Hunter Remote w/ Existing two wall switches
[ 6 Answers ]
Do I ignore the red that exists in the existing ceiling with the black, white, and ground? The red goes back to one of the switches. Does it matter which I use (black or red)? I removed an existing ceiling fan and installing another with a Hunter remote.
Thanks
Installing outlet from existing wall switch
[ 12 Answers ]
I have a switch that controls an outside light. It is at the end of the run. I want to run an outlet inside the garage from that switch. I want the outlet to only have power when the switch is on. There are two black wires attached to the switch and the two white wires are connected with a wire nut...
View more questions
Search
|