Ask Experts Questions for FREE Help !
Ask
    bergs4's Avatar
    bergs4 Posts: 107, Reputation: 3
    Junior Member
     
    #1

    Jun 5, 2009, 05:31 PM
    Wiring a Garage Shop
    Hello,

    I'm in the electrical planning stage of turning my 2 gar (approx. 400 sq. ft.) garage into a shop. I'm trying to figure out the best way to accomplish this whether it be having the electric company install a new meter or using the existing sub panel in my garage.

    A little background information that will probably be helpful:

    In the house, we have a 100amp fuse box. The line to the garage is controlled by two 60 amp fuses contained in a box that pulls out from the main fuse box (I can't remember what it's called). Also on this circuit are some house ceiling fixtures and receptacles. I have no idea when or who installed the line from the fuse box to the garage and am concerned that significant corners were cut in the installation (in terms of overloading these fuses, appropriate wire sizes, etc.).

    The wiring in the garage is haphazard and nowhere near close to code or anything reasonably safe for that matter (a lot of current carrying bare copper is exposed). I figure whichever route I take (new meter / using the existing line run from the fuse box), I will be rewiring the entire garage. I can't be sure of the wire gauge running from the house to the garage but I'm thinking maybe 6 or 8.

    Also, I will need to power my jointer, table saw, router, planer, and compressor although in all likelihood never at the same time. (As a side note, my jointer was described as 120 / 240 v; is a conversion of a tool that is 240v convertible typically a big undertakeing?

    Last, if I do ask the electrical company to install a meter, are the going to give me a hassle with permits etc?

    Thanks for the help in advance.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #2

    Jun 5, 2009, 06:21 PM

    Sounds like a 8 circuit 60 amp.
    120 to 240 on planer is a matter of connecting the right combination, usually under cover at connections or on motor.
    stanfortyman's Avatar
    stanfortyman Posts: 5,598, Reputation: 279
    Electrical & Lighting Expert
     
    #3

    Jun 5, 2009, 08:26 PM
    Quote Originally Posted by bergs4 View Post

    Last, if I do ask the electrical company to install a meter, are the going to give me a hassle with permits etc?
    Absolutely. Only this is not a hassle. It is a required part of doing this type of work.

    If you install a new service to the garage/shop, why would you think a permit and inspection were not required?

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Wiring a wood shop [ 8 Answers ]

I am building a pole barn about 225 feet from my house. I need 100 amps 220v out there for the equipment. I was hoping to use direct burial aluminum. It will be connected to the 200 amp disconnect on the outside of my house. Thank you for your help... Steve

Wiring a wood shop [ 1 Answers ]

Please help, I am putting a wood shop in my basement. I have a 15 amp circuit I will be using. I plan on running a drill press, table saw, scroll saw, disc sander and a compound miter saw of this circuit. Never will I run more than 1 at a time. These tools are not the industrial size. They...

Garage Shop Heating/AC [ 1 Answers ]

I have a 3rd bay of my Kansas home garage, walled off to make a workshop. It is about 350 sq ft with 10' ceiling, insulated walls/ceiling, single insulated overhead door. Climate is about 10 degrees winter-100 degrees summer. Gas supply & flu is not an option, nor can I have a lot of equipment...

Wiring detached shop [ 2 Answers ]

I am going to add a sub panel and wire my detached shop but have questions mainly about the neutral and ground connections. What I have is a 200A main mounted adjacent to my meter loop on the pole, then a panel mounted on the exterior of my house with breakers for things such as furnace, AC......

Need to run a sub panel to my attached garage for woodworking shop. [ 5 Answers ]

Hi all! I am a woodworker and need to install a sub panel in my attached garage. The main is a 200 amp panel and my home was built in 2001. I live in AZ and spoke with the city who said they go by the NEC 2005. I was thinking of running a 60 amp sub panel as this should more than meet my...


View more questions Search