Ask Experts Questions for FREE Help !
Ask
    jrcasey's Avatar
    jrcasey Posts: 2, Reputation: 1
    New Member
    		  
    #1

    May 31, 2009, 09:36 PM
    Galvanized floor drain to PVC
    I am replacing a shower in the basement of a house that has cast iron floor drains. I have removed the old showers and shower pans but can not remove the drain and riser from the pans. What is the best way to remove the old shower drains? What do I use to marry the cast iron floor drain to the PVC piping that is available today?

    Thanks
    Rick Casey
    Milo Dolezal's Avatar
    Milo Dolezal Posts: 7,192, Reputation: 523
    Plumbing Expert
    		  
    #2

    May 31, 2009, 10:05 PM

    Was it plastic shower pan or custom built pan ?
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
    		  
    #3

    Jun 1, 2009, 06:23 AM
    If you have cast iron drainage and a shower pan then you have a lead and oakum poured and caulked joint with one of these drains,(see images). The lead joint will have to be rremoved . To remove a poured lead and oakum joint take a 3/8" drill bit and drill a few holes down past the lead and into the oakum.. Push a screwdriver under the lead ring and lever it up. Once it's free you can began to peel the lead ring out. Now pick out the oakum and you can pull the joint apart.

    What do I use to marry the cast iron floor drain to the PVC piping that is available today?
    I would use a shilded coupling, (see image) to connect the two. Good luck, Tom
    Attached Images
       
    jrcasey's Avatar
    jrcasey Posts: 2, Reputation: 1
    New Member
    		  
    #4

    Jun 1, 2009, 08:44 AM
    Quote Originally Posted by Milo Dolezal View Post
    Was it plastic shower pan or custom built pan ?
    The shower pan was cement and ceramic tiles, it looked like it was custom built. I am replacing it with a fiberglass shower drain and shower unit.
    Milo Dolezal's Avatar
    Milo Dolezal Posts: 7,192, Reputation: 523
    Plumbing Expert
    		  
    #5

    Jun 1, 2009, 10:50 AM

    Ok, than it should be Cast Iron shower drain. That shower drain consists of 2 pieces . Those two pieces are attached together with 3 s.s. bolts. Unscrew the bolts. Lift the upper portion of drain. ( you will have some resistance here since the upper piece was put onto hot tar. ). Once off, look at the bottom part of the drain. If it has another 3 s.s. bolts than remove them and drain is free to be lifted. If it has no bolts than it can be screwed onto the pipe. It is very hard to unscrew. The best way to remove it is to carefully break it piece by piece. Once you crack the threaded area, it will get loose.

    Plastic shower base uses different type of drains. First, Dry Fit. Lay shower pan over the hole and measure how much pipe you will need to penetrate base drain opening. Then cut piece of pipe and install onto old pipe.

    You will need some support for the new base. Use light weight mortar. Mix it up thin, put under the base in several small blobs and set base into it. Make sure the pan will go all the way down and now is touching the concrete floor. Step inside if you have to and gently "dance" inside until there is no gap between lip of the base and floor.

    Now, install upper part of new drain. Since you are using Plastic Pan you won't use drain heads as posted by Tom. Those are for custom shower pans. The actual drain should come with your shower pan kit. If not. There should be instructions which one to get. But Home Depot carries quiet a large selection of such a drains.

    Good luck... and let us know how you did... Milo
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Basement washer drain connection to existing floor drain [ 10 Answers ]

I am on city service. I would like to connect my basement washer drain into the existing floor drain (3" line). I cut the line about 3 feet down from floor trap and installed a 3x2inch y. This existing floor drain takes a 45 turn about 6" down from where I cut it. The 2 inch will drain the washer ....

Splicing into combo cast irion/galvinized pipe [ 3 Answers ]

My objective is to relocate the basement washer and utility sink to the wall in front of an existing wet stack and tap into the stack for drainage in my NJ home. I have 2 questions: is there a minimum height requirement from the floor to the bottom of the standpipe’s P-trap, and what is the best...

2nd Floor, Floor drain backing up with water in restroom [ 1 Answers ]

I have a second floor restroom at my workplace and there is a little bit of water backing up and some sewer gas smell. There is rarely anything that goes down that drain but there is a little water in it that I can see. Also it seems that the urinals in the same restroom are draining very slowly....

Raising a floor drain in concrete floor [ 2 Answers ]

I have an old concrete floor with a newer pvc type drain. The floor slopes about 1.5" over 2' around the drain so I would like to raise the drain in order to level the floor to install ceramic tiles. I'm still going to ensure the floor slopes toward the drain just enough. I figure I need to...

Converting cast iron floor drain to shower drain [ 3 Answers ]

I am adding a bathroom to my basement, which has partial (complete? ) plumbing already roughed into the floor (in 1976). Sewage lift station (vented) is 3 ft from 4" styrofoam plug (toilet), 4 ft from 1 1/2 inch cast male pipe end extending through floor (lav, have already added vertical vent...

View more questions Search