Ask Experts Questions for FREE Help !
Ask
    liparalegal's Avatar
    liparalegal Posts: 1, Reputation: 1
    New Member
    		  
    #1

    May 12, 2009, 10:41 AM
    No Hot water, repleced electric heater!
    Had no hot water yesterday. Hubbys friend replaced the heating element but still did not work. Then they decided to buy a 2 yr old used one which they installed, still no hot water. Then they went and found out that the panel box circuitbreaker for the heater was burned so replaced breaker, still no hot water. They checked thermostat, dip tube, etc. What else should we check and how to obtain hot water???? Thanks Rob and Liz in PA:o
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
    		  
    #2

    May 12, 2009, 11:01 AM

    Your friend is using the hit or miss method, you need to do some diagnostics first. Lets start with that breaker, what did they install and have they/you verified that 240 is reaching the heater?
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
    		  
    #3

    May 12, 2009, 12:03 PM
    Hi all:

    My bet here is that the friend doesn't know how to test for 220-240V or he would have by now..?

    Like Ballengerb1 said... need to start at the basics. First need to confirm that each leg of the 30 amp double pole breaker is sending 110-120V to the heater. If both legs have 110-120V (gives the 220-240V total) then you move to the heater junction box (top of heater) and confirm 220-240V there. Once power is confirmed at the junction box, you will want to test for power at the top element ONLY as power will not be sent to the bottom thermostat/element until the top thermostat/element is satisfied... O.K.?

    If no power to the top element after confirming power into the heater then the top thermostat is bad.

    Pop back and let us know what you discover...

    MARK
    afaroo's Avatar
    afaroo Posts: 4,006, Reputation: 251
    Ultra Member
    		  
    #4

    May 12, 2009, 12:36 PM

    Both Bob and Mark have stated very well, I will also add the following link just for info, good Luck.

    John

    How to Test a Water Heater Thermostat - wikiHow
    letmetellu's Avatar
    letmetellu Posts: 3,151, Reputation: 317
    Ultra Member
    		  
    #5

    May 12, 2009, 06:27 PM

    Some heaters have a reset button on the thermostat, just in case you don't find the problem elsewhere.
    andrewc24301's Avatar
    andrewc24301 Posts: 374, Reputation: 29
    Full Member
    		  
    #6

    May 12, 2009, 08:23 PM
    I will add:

    When testing for the 240 volts, make sure to test between the two hot wires. (one lead on one hot wire, the other lead on the other hot wires.

    Testing each wire to ground will give a false reading as voltage will read through the element giving the appearance of 120 volts on both sides to ground even if one side of the 240 has dropped out.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Electric Water Heater [ 14 Answers ]

Have a Whirlpool Electric Water Heater which is failing to heat water. Have replaced the heater, the elements, & the thermostat. Water heated for a month or so, and now won't heat. Whirlpool has been of no assistance what so ever. Not sure it's a plumbing problem or electrical problem. Heater...

Electric Water Heater [ 4 Answers ]

There is no water flowing out the hot water side of all sinks, showers, tubs and washer. Problem with the hot water heater?

My Electric Water Heater is not filling up OR heating water! [ 2 Answers ]

First: Does the breaker have to be on for my water heater to fill up? I turned the breaker on after draining it a little, and it isn't filling it back up... Second: How long should I have to wait for my water heater to heat the water again?

Replaced electric water heater Atlanta area, but no hot water [ 14 Answers ]

The old water heater died. Bot one (38 gals) at HD. Installed exactly like the old one was as follows--3 CPVC pipes come out of wall. Two are joined. Before they are joined one has a valve. After they are joined there is a second valve. The pipe is connected to the cold side of the heater using...

Electric Water Heater [ 7 Answers ]

Howdy all again, here's another question. If you read my previous post about Water Circulator Woes, we're going to move upstairs now. My 20 gal electric water heater is pulling too much power. It's discoloring the electrical faceplate, and it actually burnt through it's power cable. But it...

View more questions Search