Ask Experts Questions for FREE Help !
Ask
    muggles's Avatar
    muggles Posts: 4, Reputation: 1
    New Member
    		  
    #1

    Sep 28, 2006, 02:09 PM
    Oops, goofed on shower base
    My brother in law helped me (or I helped him) install a new shower (base, walls, enclosure) we finsihed yesterday, but neglected to put a mortar bed beneath the shower base. Here's my question: can I take out the shower base, put down some mortar and re-install the base or is it too late? It doesn't look like it would be too much trouble to re-do and maybe I can do it without bothering him. (Carefully remove, and then carefully replace, recaulking, etc. I would rather do this now than have a leak later.

    Thanks for any help.
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
    		  
    #2

    Sep 28, 2006, 03:09 PM
    It depends, can you get under the base without tearing it all apart? The shower drain's glued in and the enclosure walls set on the base. If you could make a cut in a wall to get in and bed the shower floor it might be a better way to go. Regards, Tm
    Knucklez's Avatar
    Knucklez Posts: 129, Reputation: 2
    Junior Member
    		  
    #3

    Sep 28, 2006, 05:21 PM
    I'm going to ask a stupid question...

    Are you sure you need a mortar base? My plastic shower neo-angle base was a "mortar optional" type because the base was all reinforced with metal square pipes.

    Knucklez
    muggles's Avatar
    muggles Posts: 4, Reputation: 1
    New Member
    		  
    #4

    Sep 29, 2006, 08:34 AM
    That's not a stupid question. The shower base is one of those rigid re-inforced pvc things, no metal. It gives a little when I step on it.
    muggles's Avatar
    muggles Posts: 4, Reputation: 1
    New Member
    		  
    #5

    Sep 29, 2006, 08:50 AM
    No, speedball, I don't think I can get under the base without tearing something apart. One wall is unfinished at the moment , with the studs showing and therefore, part of the base is in view, but the drain is glued and the enclosure walls attached. There's no way under without undoing something, is there? Would it be best to just let it stay as is? Everything appears to be tight and leak free. The shower base flexs a little when stepped on. Does no mortar guarantee a leak some time in the future? Should I just wait and see? My previous shower base never leaked until my daughter dropped a heavy bottle and broke out a tiny section... (and this one had no mortar, either).

    Thanks for any suggestions. I kind of hate to take the base up, since it will just be me and my sister doing it.
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
    		  
    #6

    Sep 29, 2006, 10:05 AM
    You don't have much of a choice. Tearing out the base on a "MAYBE" doesn't cut it with me either. I would give it a shot the way it is. If it doesn't develop a leak then you're ahead of the game and if it does then click on back and we'll explore options. Good luck, Tom
    muggles's Avatar
    muggles Posts: 4, Reputation: 1
    New Member
    		  
    #7

    Sep 29, 2006, 10:21 AM
    Thank you. What a relief. I'm going to leave it as is and hope it continues to be leak free. If not, I will surely be back with questions.

    Thank you from a grateful (and still sore from crawling under the house) do-it-yourself-er.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Installing shower base [ 6 Answers ]

Tom, I have a new question. In setting a shower base, on concrete, how much mortar should a person spread, just a couple inches around the drain? Or, should it be more than that. Also, what's the deal in the instructions about putting plastic over the mortar? The base wouldn't be stuck down with...

Shower base... [ 7 Answers ]

Not sure if this is a pluming question or tiling question, so sorry if this is the wrong place to ask. I'm still working on my master bathroom project (some of you may remember me from my "moving a toilet" question). Well, everything is roughed in in its new locations and I am starting to...

Removing shower base in basement [ 6 Answers ]

We are replacing a shower in the basement 32 x 48. We finally got the base off by cutting around it to get it out because the center drain connection was so attached we couldn't remove it any other way. I have photos attached. We are chiseling away now to get to the bottom of this brass drain...

Concrete Shower Base [ 2 Answers ]

I am trying to replace what was an all plastic shower stall located in my basement with a more substantial structure. All of the plumbing is in place but as part of my project I have studded out one wall so that I could re-route the hot and cold water lines inside the new wall. Because of this...

Shower stall base [ 3 Answers ]

I purchased a house with an unfinished half bath. The shower base was not installed. There is a cast iron pipe coming up through the slab.there is a drain leaded into the pipe with a flange and a liner that is cut off,and a threaded 2" drain screwed into it,it has been there a long time and I...

View more questions Search