 |
|
|
 |
New Member
|
|
Aug 29, 2006, 09:25 PM
|
|
95 F150 AC Compressor
These 107 degree days took a toll on my truck's a/c compressor, got too hot and blew off the freon cap. I took the truck to a mechanic who quoted $600 to $1,000 to replace the compressor. I could see the damage to the compressor. I can buy a re-built compressor for $175 with a year warranty.
In this model F150 the compressor sits right on top and in the front of engine. Looks easy to get to. My wife is mechanically inclined and says we can do this ourselves. There's not much she can't figure out how to do. But she does say, if we had a schematic of the compressor and belt placement, we would have a easier venture.
So, I'm looking for anyone who has replaced a 1995 F150 compressor and could give us some insight in this subject.
Thank You, Gary
|
|
 |
Junior Member
|
|
Aug 29, 2006, 10:31 PM
|
|
You should be able to get the diagram from a Haynes manual you can buy at
An auto parts store for about $15 if no one here can help you.
The replacement of the compressor should not be a hard job to do but
Be aware when hooking the hoses back up to the new compressor to use the
Special seals that are required.
If you do not have the knowledge or equipment and gauges to recharge the
System you can have the truck towed to a shop where they would only
Charge to do the recharge, in any case you would save a lot of $ and could
Probably do it for no more than $500.
|
|
 |
Senior Member
|
|
Aug 30, 2006, 09:10 AM
|
|
If you decide to do it yourself, be sure to also replace the receiver/dryer and the orifice tube, because they have trapped crud from the bad compressor. If your vehicle has the new style quick connect AC lines, you will need to buy a Lisle AC/Fuel Line Disconnect Kit (part#37000) for about $10. If you or a friend have a membership to Sam's Club, they are unloading their stock of R-134a freon @ $37.62 for a case of 12 cans. This is much cheaper than the $8-$12 per can from an auto parts store. Also be sure to follow directions for the proper amount of PAG oil in the system. Good luck.
|
|
 |
Junior Member
|
|
May 17, 2007, 08:25 PM
|
|
 Originally Posted by G Trell
These 107 degree days took a toll on my truck's a/c compressor, got too hot and blew off the freon cap. I took the truck to a mechanic who quoted $600 to $1,000 to replace the compressor. I could see the damage to the compressor. I can buy a re-built compressor for $175 with a year warranty.
In this model F150 the compressor sits right on top and in the front of engine. Looks easy to get to. My wife is mechanically inclined and says we can do this ourselves. There's not much she can't figure out how to do. But she does say, if we had a schematic of the compressor and belt placement, we would have a easier venture.
So, I'm looking for anyone who has replaced a 1995 F150 compressor and could give us some insight in this subject.
Thank You, Gary
Freon... what about freon
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Ford f150 charging problems
[ 5 Answers ]
My f150 battery smells like eggs and will not hold a charge I replaced the battery and the att. Still over charges and battery goes dead over night both are new replaced 3 times now any ideas would be great drawing a blank on this one
Compressor Map
[ 2 Answers ]
I am working with refrigeration systems for some research. I am looking at the compressor map and have been told that a correction factor of .75 is fair to assume for conditions outside of the map's designated superheat and intake temp. Does anyone know where I can obtain any articles to support...
A/c compressor won't kick in
[ 4 Answers ]
I have a window a/c unit with a compressor that won't kick in. I took the unit apart and noticed the control wire on the compressor looked burnt and corroded. I took the wire off and put a new connector on, but still no go. I noticed however when I left the control wire disconnected I could hear...
Air Compressor
[ 3 Answers ]
I have a new air compressor for my hot rod fabrication. The specifications are as follows,
5.5hp 80gal 24amp 240v. My question is, it calls for a 30 amp breaker and time delay fuse, Type "T". I am running 6/2 wire to supply the unit, it is about 90 ft from the main panel so we ran 6/2 for minimal...
View more questions
Search
|