Ask Experts Questions for FREE Help !
Ask
    hookmaster's Avatar
    hookmaster Posts: 3, Reputation: 1
    New Member
     
    #1

    Feb 28, 2009, 08:46 PM
    Reduction of amps from main pole to workshop
    Hi,
    I am trying to figure out how I can reduce my 200 amp service down to 100 amps for my workshop. The panel in the workshop is rated at 100 amps and the only place that I can tie in is a 200 amp ON/OFF main shutoff just underneath the meter can on my service pole. BTW, I still have to carry the full 200 amps down the pole to my house.
    stanfortyman's Avatar
    stanfortyman Posts: 5,598, Reputation: 279
    Electrical & Lighting Expert
     
    #2

    Feb 28, 2009, 10:14 PM
    You'll need to replace the disconnect at the pole with a 200A feed-through panel.
    This will let you carry the full 200A to the house and also install a 100A (or less) feeder breaker to feed the shop.
    hookmaster's Avatar
    hookmaster Posts: 3, Reputation: 1
    New Member
     
    #3

    Feb 28, 2009, 10:26 PM

    Thank you sooo much for your help. I just don't understand why they couldn't tell me that at Lowe's. They kept wanting me to buy a box for this, a subpanel for that... spend, spend, spend!
    Again, thank you!!
    hookmaster's Avatar
    hookmaster Posts: 3, Reputation: 1
    New Member
     
    #4

    Feb 28, 2009, 10:44 PM

    Just an afterthought... Does Lowe's or somewhere like that sell a 100 amp feeder breaker with lugs large enough to handle the 3 ga wire I have run to the pole, or will this have to be gotten from an electrical supply house?
    stanfortyman's Avatar
    stanfortyman Posts: 5,598, Reputation: 279
    Electrical & Lighting Expert
     
    #5

    Mar 1, 2009, 06:05 AM
    Most 100A breakers will handle at least #2, so you are fine with #3.
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
     
    #6

    Mar 1, 2009, 11:29 AM

    Folks need to be cautious regarding advice from home centers. If home centers actually employeed plumbers and electricans it might be safe to accept their advice but they don't. It is safer to see what several experts here, and on other sites, have to say.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

From double pole to single pole thermostat -2 extra leads [ 3 Answers ]

The double pole thermostat for the baseboard heater has a red and a black wire coming in (from the circuit panel) and a red and a black going to the heater. The new single pole only has a red LINE lead and a black LOAD lead. If I attach red to red and then black to black, I have black (from...

Cost to upgrade from 100 amps to 200 amps and ground [ 4 Answers ]

StanFortyMan has made a lot of sense about my needs in a home with a 100 AMP Service.. I would like to upgrade to 200 amps.. with some ground sockets(or whatever this is called) and put in more sockets... The house is 1300 square feet... does anyone have a guestimate of costs?? Thanks, Annie

12 Amps on Water Main! [ 9 Answers ]

I've got a problem with the grounding in my neighborhood, and I need some help in getting the right solution. I noticed high EMF throughout much of my house, even with all appliances turned off. I shut off all power to the house at the main breaker, and there was no improvement in the...

Replace a two pole breaker in main panel box [ 1 Answers ]

I need two replace a bad two pole breaker in main panel boxwhat tools do I need

Double pole or single pole thermostat for baseboard heater [ 2 Answers ]

A more specific question here: My 240v baseboard heater says it can be wired with a single or double pole thermostat. Since 240v is already "dual pole" with two hots, do I want to stick with a double pole thermostat? Are there advantages/disadvantages to each? Thanks.


View more questions Search