Ask Experts Questions for FREE Help !
Ask
    Johannes W's Avatar
    Johannes W Posts: 9, Reputation: 1
    New Member
     
    #1

    Feb 1, 2009, 11:22 AM
    Cutting galvanised pipe with a metal blade saw.
    Can I cut a 3" galvanized pipe with a metal blade saw ?
    I am trying to replace a piece of drain pipe located in the bsmt ceiling with abs pipe.
    There is about 2'' space between the ceiling and the pipe, and I will have to cut above my head. Renting a special cutter is an option but expensive as it is such a small job.
    bones252100's Avatar
    bones252100 Posts: 253, Reputation: 29
    Full Member
     
    #2

    Feb 1, 2009, 12:23 PM

    Personnally, a side cutting power tool is preferred. In your situation, a hacksaw can be used cutting from the bottom upward. You will be there a while & use every cuss word in your vocabulary but it can be done. Allow no showers, toilet flushing, dishwashing, etc. as this may be pouring on your head. Good Luck!
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #3

    Feb 1, 2009, 12:31 PM

    An angle grinder works with the right blade.
    Milo Dolezal's Avatar
    Milo Dolezal Posts: 7,192, Reputation: 523
    Plumbing Expert
     
    #4

    Feb 1, 2009, 12:31 PM

    Rent a sawzall from Home Depot for couple of hours. Buy a good "ExTreme" metal blade at the same place. It will cut through safely and the way it should - even when the pipe is overhead and in tight space.
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #5

    Feb 1, 2009, 01:13 PM
    Like Milo said, rent or purchase a reciprocating sawzall... you will use it again I bet! It will make quick work of this for you. Be sure to buy a long bi-metal sawzall blade and wear safety goggles as well... ;)

    Be careful to support the pipe(s) as you work and use a SHIELDED CLAMP (see picture) to make the transition from galvanized pipe to ABS plastic. You would order a 3" plastic x 3" plastic shielded clamp (even though going to galvanized pipe... same sizes).

    Good luck.

    MARK
    Attached Images
       
    Milo Dolezal's Avatar
    Milo Dolezal Posts: 7,192, Reputation: 523
    Plumbing Expert
     
    #6

    Feb 1, 2009, 01:49 PM
    Quote Originally Posted by Milo Dolezal View Post
    Rent a sawzall from Home Depot for couple of hours. Buy a good "ExTreme" metal blade at the same place. It will cut through safely and the way it should - even when the pipe is overhead and in tight space.
    Johannes, Ratchet cutter is for Cast Iron. Cast Iron "snaps" when under pressure. Galvanized pipe will not. You need to cut it.
    Johannes W's Avatar
    Johannes W Posts: 9, Reputation: 1
    New Member
     
    #7

    Feb 1, 2009, 04:00 PM
    Quote Originally Posted by Milo Dolezal View Post
    Rent a sawzall from Home Depot for couple of hours. Buy a good "ExTreme" metal blade at the same place. It will cut through safely and the way it should - even when the pipe is overhead and in tight space.
    I am now wondering is it cast iron or galvanised pipe I want to cut.
    Thanks Very much for so much pointed free advise.

    Johannes
    Johannes W's Avatar
    Johannes W Posts: 9, Reputation: 1
    New Member
     
    #8

    Feb 1, 2009, 04:14 PM
    I just checked the pictures I had taken and it definitely looks like galvanised pipe.
    I am not sure how I can share these picture on the net?
    Both ends of the pipe are treaded on to the cast iron stack, in a Y at one end and as a connector at the other end. Would it be possible to unscrew this pipe at all?
    I would be glad to email the pictures.

    Thanks for all the help.

    Johannnes.
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #9

    Feb 1, 2009, 05:57 PM

    Post pictures using Go Advanced/Manage attachments. Use the free program IrfanView - Official Homepage - one of the most popular viewers worldwide to re-size if necessary.
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #10

    Feb 1, 2009, 06:14 PM
    Johannes W...

    Galvanized pipe is typically silver or gray and is threaded. Cast iron pipe is distinctly black and (usually) has no threads.

    Check out the picture below. You can see the galvanized pipe coming out of the top of the cast iron fitting (on bottom). PVC plastic pipe goes to the left.

    Which pipe looks like your pipe?

    Let us know.

    MARK
    Attached Images
     
    Johannes W's Avatar
    Johannes W Posts: 9, Reputation: 1
    New Member
     
    #11

    Feb 1, 2009, 11:41 PM
    Quote Originally Posted by massplumber2008 View Post
    Johannes W...

    Galvanized pipe is typically silver or gray in color and is threaded. Cast iron pipe is distinctly black and (usually) has no threads.

    Check out the picture below. You can see the galvanized pipe coming out of the top of the cast iron fitting (on bottom). PVC plastic pipe goes to the left.

    Which pipe looks like your pipe?

    Let us know.

    MARK
    Thanks Mark.

    Definitely Galvanized pipe. Tell me how I can arttach a picture to the message,
    So you can see if I might be able to unscrew it?

    Johannes
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #12

    Feb 2, 2009, 01:13 AM

    POSTING PICTURES AGAIN:

    https://www.askmehelpdesk.com/plumbi...ml#post1521654
    afaroo's Avatar
    afaroo Posts: 4,006, Reputation: 251
    Ultra Member
     
    #13

    Feb 2, 2009, 02:42 AM

    Here is how you attach a picture to the post.
    1. Click on advance.
    2. When the page opens, Click on the attachment icon is on right side of smile face.
    3. Manage attachment will open.
    4. Click Browse, the Choose file window will open.
    5. select your pictueres and double click wait untell the picture is uploaded in the top Browse box.
    6. Click the top upload button on the righ, wait until you see the link shows in the upload file from a URL.
    7. Close the manage attachments window.
    8. Click Submitt Answer and you are done, Good Luck.

    John
    Johannes W's Avatar
    Johannes W Posts: 9, Reputation: 1
    New Member
     
    #14

    Feb 2, 2009, 10:35 AM
    Quote Originally Posted by afaroo View Post
    Here is how you attach a picture to the post.
    1. Click on advance.
    2. When the page opens, Click on the attachment icon is on right side of smile face.
    3. Manage attachment will open.
    4. Click Browse, the Choose file window will open.
    5. select your pictueres and double click wait untell the picture is uploaded in the top Browse box.
    6. Click the top upload button on the righ, wait untill you see the link shows in the upload file from a URL.
    7. Close the manage attachments window.
    8. Click Submitt Answer and you are done, Good Luck.

    John
    Great John, I will try thisright now.
    Johannes W's Avatar
    Johannes W Posts: 9, Reputation: 1
    New Member
     
    #15

    Feb 2, 2009, 10:39 AM

    Here are the pictures. Is there a way to unscrew this pipe. Pictures show both ends of the pipe. Also the othe side of the cast iron conName:  BSMT Bath leak.jpg
Views: 2931
Size:  30.7 KB

    Name:  BSMT Bath leak (8).jpg
Views: 2838
Size:  26.9 KB

    Name:  BSMT Bath leak (6).jpg
Views: 3068
Size:  107.2 KBnector on other side.
    Milo Dolezal's Avatar
    Milo Dolezal Posts: 7,192, Reputation: 523
    Plumbing Expert
     
    #16

    Feb 2, 2009, 10:47 AM

    It appears to me it is painted galvanized pipe (pic 2) that attaches to Cast Iron Hub fitting ( pic 1).

    Cut off this galvanized pipe about 2" before Left and Right fittings. Here, be careful: it is heavy and will drop down quickly as you cut. Have somebody else to hold the pipe while you cut it. Wear gloves and goggles. Insert ABS pipe and connect with No-Hub / Fernco couplings. I doubt you will be able to unscrew the piece one side as shown in pic #2 and 3.
    Johannes W's Avatar
    Johannes W Posts: 9, Reputation: 1
    New Member
     
    #17

    Feb 2, 2009, 01:47 PM

    Great response and answer.
    Cutting with a metal saw (hacksaw) I understand now will be very hard.

    Thanks Milo

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Sparks from cutting metal dangerous? [ 4 Answers ]

I have a metal bar that is used with a key as a shut-off for a gas line that goes into my fireplace. The bar sticks up from the floor about an inch. It is a tripping hazard for my daughter who walks near that area often. If I cut it off to the floor level, will the sparks created be any hazard...

Removing the cutting blade [ 2 Answers ]

I have a Yard machine riding lawn mower.Can some body tell me how to take the cutting blade out for me so I can sharpen them.

Bending schedule 40 galvanised pipe [ 1 Answers ]

Is it possible to bend the schedule 40 galvanised pipe to get curve about 30-45 degrees of angle? The temperature of the water flowing in it is max 50 degrees C and the pressure is 6 bars it will be a shower connection between shower nosle and shower mixer.:mad: :mad: :confused: :mad: :confused:

How to clean out galvanised pipe [ 4 Answers ]

So the line to the house has lots of pressure, tested it outside. But here is where it gets tricky. MOst of the pipe is galvanized, that goes to copper. There is very little pressure throughout the house, and its well pretty pathetic. So since the pressure is great outside, we figure the...


View more questions Search