Ask Experts Questions for FREE Help !
Ask
    monchar88's Avatar
    monchar88 Posts: 5, Reputation: 1
    New Member
     
    #1

    Jan 24, 2009, 09:45 AM
    How much heat can flexible copper pipe take?
    We are using a pellet stove to heat our baseboard hot water system. We have propane furnace as a back up. My husband ran copper pipes on the out side of the burn box and inside the burn box. All has been fine for 2 years until last night. He didn't turn the stove off the clear the blower box of some dust so we got 1 leak on the outside. We drained the lines and soldered the joint. As we turned the water back on and purged the air it looked fine. I guess we got a air lock on the pump that runs the water through the stove cause we now have water squirting all over. We used small pieces of pipe and 90 elbow close together to nestle the pipe, to get as much heat as we could. We now face replacing the pipe in the fire box. THE MAIN QUESTION IS: Can flexible copper pipe take the heat of the fire box like rigid copper pipe? It would be easier to coil the pipe in there than solder all those joints again just right to get them in the fire box. Thank you sorry so long
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #2

    Jan 24, 2009, 12:37 PM

    The tubing can, but plumbing solder is the weak link.

    Can you braze/silver solder?
    monchar88's Avatar
    monchar88 Posts: 5, Reputation: 1
    New Member
     
    #3

    Jan 24, 2009, 08:21 PM
    Yes my husband thought it would be best to use silver solder and map gas to fit the fittings together. The cost of the flexible pipe might be high but there will be less joints in the fire box. He also looked online and found somethinkg like using heat exchangers in the fire box. What do you think woud be the bet way to do this. We could bring out all the current copper piping, replace it with a heavier guade and use the silver solder and the map gas as an alternative. What do you think?
    Milo Dolezal's Avatar
    Milo Dolezal Posts: 7,192, Reputation: 523
    Plumbing Expert
     
    #4

    Jan 24, 2009, 11:22 PM

    Yes, coiled, type L, "soft" copper is same as rigid type L copper. If you are really skeptical use type "K" copper. It is really Heavy Duty, thick wall, copper pipe. As KISS mentioned in his post, the soldered joint is the weak point. Since coiled copper comes in 60' lengths, you may avoid joints in direct heat. Leave joints outside and use only continuous pipe as heated element. If you use Silver rods to seal joints than you are welding. Weld should withstand the furnace heat.
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #5

    Jan 28, 2009, 12:10 PM

    There is some info at Copper.org: Copper Development Association - Information on copper and its alloys.. Specifically about how to braze copper pipe.

    A commercial heat exchanger would be your best option for highest efficiency.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Copper L pipe to black iron pipe [ 19 Answers ]

Hello This is a natural gas application. Can flexible L copper pipe be coupled to black iron pipe and then buried? I will paint and wrap the black pipe before burial. Thanks Ruko

Galvanized pipe to either Copper/CPVC pipe [ 14 Answers ]

I had a leak in my cold water feed which happens to be galvanized pipe. It was between 2 floors and I cut out the affected section. I am going to replace the cut out section with either copper or CPVC. But how does one connect unthreaded galvanized pipe to the after mentioned pipes? I don't know if...

Copper pipe to iron pipe [ 2 Answers ]

How would you connect a 1/2" copper pipe to a 1/2" galvanized iron pipe that has been cut and has no threads? Do I need to re-thread the iron pipe, screw on a brass attachement and solder the other end to the copper? If so, what is the name of the tool use to re-thread the iron?

Copper to pvc pipe [ 7 Answers ]

We are trying to install a water system in our home and need to know how we go from copper pipe to pvc pipe.

A/C not cooling, Small Copper pipe COLD and Large Copper pipe room temp. [ 4 Answers ]

I just moved into a newly constructed townhome and the a/c units are of course new. The A/c is not cooling at all. The machine inside turns on as well as the one outside. The inside A/C makes a strange sucking sound kind of like if you were sipping something out of a cup with a straw and you ran...


View more questions Search