Ask Experts Questions for FREE Help !
Ask
    Soonrbtexn's Avatar
    Soonrbtexn Posts: 1, Reputation: 1
    New Member
     
    #1

    Nov 18, 2008, 04:11 PM
    RTH6300B Honeywell Thermostat
    I recently installed the RTH6300B programmable thermostat. The a/c worked fine after installation, but I am now trying to get my gas furnace fired up and am having a problem with the pilot light staying lit on the furnace. I'm wondering if I have installed the thermostat improperly so that it doesn't convey the right signal to the furnace?? I had 4 wires coming out of the wall, G, Y, W, R and have hooked the R to the R on the thermostat. There is a jumper from R to RC and I'm wondering if the jumper needs to be raised up?? Does it stay down?? Could this be why my pilot light won't stay lit?? I've used the furnace for the past 10 years with no problems lighting the pilot, and the only new thing is the thermostat. Help please... I'm tired of being cold at night!! Thanks.
    nathen171's Avatar
    nathen171 Posts: 5, Reputation: 1
    New Member
     
    #2

    Nov 18, 2008, 04:33 PM

    I'm not the greatest at gas I am hvac certi. But I do know your jumper wire has a lot to do with your furn. I can't tell without seeing but make sure you got the right kind of therm. It has to be one that works for gas! A standard therm won't work on gas
    mygirlsdad77's Avatar
    mygirlsdad77 Posts: 5,713, Reputation: 339
    Plumbing Expert
     
    #3

    Nov 18, 2008, 04:42 PM

    How old is your furnace, what make and model is it. If it has a standing pilot, the thermostat shoudnt have anything to do with the pilot staying(or not staying) lit. Most likely you have a bad thermocouple. Let me know what you think.
    wmproop's Avatar
    wmproop Posts: 3,749, Reputation: 91
    Ultra Member
     
    #4

    Nov 18, 2008, 07:28 PM
    Quote Originally Posted by nathen171 View Post
    im not the greatest at gas i am hvac certi. but i do know your jumper wire has a lot to do with your furn. i can't tell without seeing but make sure you got the right kind of therm. it has to be one that works for gas! a standard therm won't work on gas
    I`m wondering why
    mygirlsdad77's Avatar
    mygirlsdad77 Posts: 5,713, Reputation: 339
    Plumbing Expert
     
    #5

    Nov 18, 2008, 07:48 PM

    Okay, so you hold in the pilot knob, light the pilot. Does the pilot light while you are holding in the knob?. Im assuming yes. When you let of the knob(after holding it for a minute), the pilot goes out? If so, you need to replace thermocouple, end of story(there is a very small chance that it is a bad gas valve, wouldn't even think about that until you replace thermocouple)..

    If you can't even get the pilot to light, then you probably have a plugged pilot orifice. Let me know what's going on, and I would love to help. As of right now, I feel like I'm typing to myself.
    MarkwithaK's Avatar
    MarkwithaK Posts: 955, Reputation: 107
    Senior Member
     
    #6

    Nov 18, 2008, 08:34 PM
    Quote Originally Posted by nathen171 View Post
    im not the greatest at gas i am hvac certi. But i do know your jumper wire has a lot to do with your furn. I can't tell without seeing but make sure you got the right kind of therm. It has to be one that works for gas! A standard therm won't work on gas
    Huh!!

    The jumper goes from Rh to RC unless you have a dual transformer system. The stat will have nothing to do with your pilot not staying lit.
    mygirlsdad77's Avatar
    mygirlsdad77 Posts: 5,713, Reputation: 339
    Plumbing Expert
     
    #7

    Nov 18, 2008, 08:39 PM

    I agree that nathan didn't make much sense, but lets try to help the asker, shall we.
    MarkwithaK's Avatar
    MarkwithaK Posts: 955, Reputation: 107
    Senior Member
     
    #8

    Nov 18, 2008, 08:40 PM

    I am trying lol. He asked about the jumper wire.
    mygirlsdad77's Avatar
    mygirlsdad77 Posts: 5,713, Reputation: 339
    Plumbing Expert
     
    #9

    Nov 18, 2008, 08:57 PM

    Yep, can't help the unhelpable

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Thermostat replacement with honeywell rth6300b [ 1 Answers ]

I have a trane weatehrtron - 7 wires from the wall and cannot find the right connection to the new honeywell rth6300b. I tried the wiring wizard and found I have 8 wired coming out of the wall and no place to hook them up... I end with the B, T , O and X2 left without a connection - help anyone?

How to connect wires to a RTH6300B honeywell thermostat [ 2 Answers ]

I only have 2 wires to connect I removed the old wires from the W and R connection And put them on the new one but nothing happens. Any help would be appreciated

Problem with New Honeywell RTH6300B Thermostat [ 5 Answers ]

We have a Frigidaire model B3BM-024K-A HVAC system. It is all electric. A few days ago, my husband replaced the old thermostat with a Honeywell RTH6300B programmable one. My husband wired it according to the instruction. It has a problem: the heat will not switch off automatically when the...

Honeywell RTH6300B Thermostat setup [ 1 Answers ]

I am trying to install a Honeywell RTH6300B to replace a Honeywell 3-wire thermostat. The wiring on the old thermostat is: Red wire – R terminal White wire – Y terminal Green wire – W terminal There are no other wires. The system is an oil burner with hot water baseboard heating. There...

Honeywell Programmable Thermostat RTH6300B [ 2 Answers ]

Since I live in Canada I want a programmable thermostat that uses celsius. Do you know if this model can be switched from Fahrenheit to Celsius? IF so how is this done? I've not opened the package since I wanted this anwer first. Thanks for your help.


View more questions Search