Ask Experts Questions for FREE Help !
Ask
    mcd176's Avatar
    mcd176 Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Oct 10, 2008, 07:16 PM
    Fan Control Center wiring
    Hello,

    I need help!! I have a White-Rodgers/Steveco 90113 Fan Control Center with a SPDT relay. I need to know how to wire it, I have a thermostate with the red and green wires running to the fan control center, all I need to do is run a single stage fan on my Ducane furnace so the blower will kick on to heat my home from my outdoor wood boiler. The fan control center has a BLACK, RED and Brown Wire coming from it, when I hooked the 110 power into the transformer and the Red thermostat wire to ""R" and the Greeg thermostat wire to the "G" and the thermostat clicked the transformer but I have no power to run the fan on the red, black or brown wire coming from the relay? Please help I need heat.
    letmetellu's Avatar
    letmetellu Posts: 3,151, Reputation: 317
    Ultra Member
    		  
    #2

    Oct 10, 2008, 07:36 PM

    You need to be more precise on your terms, tell us about the motor where are the wires to it connected.
    I would think that the only function of the SPDT relay would be is to power the motor.
    mcd176's Avatar
    mcd176 Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Oct 10, 2008, 07:51 PM
    You are correct, I need to power up my fan that is already in my ducane furnace, I had done this previousley but the relay went bad and I forgot how I wired it, Basically I need to connect the fan control center to the thermostat for heat only and need to know what single wire I need to hook to the motor for positive power since it is already grounded at the furnace
    Missouri Bound's Avatar
    Missouri Bound Posts: 1,532, Reputation: 94
    Ultra Member
    		  
    #4

    Oct 10, 2008, 08:10 PM
    Sounds like you are controlling the relay but not switching the load. Remember that the relay is just an electrically operated switch. If the relay is working, then you need to make sure that the energized relay closes the contacts which the fan is connected to.
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #5

    Oct 10, 2008, 09:46 PM
    Everything you need to know is right below.

    http://www.white-rodgers.com/wrdhom/.../0037-5786.pdf
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Fan Control Center Wiring [ 5 Answers ]

I'm trying to make this old Magic Chef furnace work in my garage. I got it and the Fan Control Center was broken, laying inside unwired. I have no wiring diagram for this unit but the M# is G76-7502 C2-5. I need help wiring the fan control center and the fan limit switch to power. I bought a new...

Rheem Furnace Fan Control Center Transformer [ 2 Answers ]

I was replacing my transformer/fan control center for a Rheem Furnace (central Heat/air) and did not label the wires. I am now very confused... I have two sets of contact wires coming out of the relay, one set "no" and the other "nc". And the Primary wires on the transformer... How do I connect...

Fan control center to blower [ 1 Answers ]

I have a white rogers-steveco 90-113 fan control center and I would like to know how to wire it to my airco hot air furnace so I can use the blower for my outdoor wood boiler and also how to wire the thermostat to the fan control

Outdoor eletrical wiring (switches, control center) [ 1 Answers ]

I was curious if anyone knows of a "control center" type device for outside wireing... I've wired up quite a few indoors, but I know those indoor ones are NOT for outdoors because they are not water tight and most don't even have covers for the switches. Basically what I need is an outdoor box...

Fan Control Center Wiring [ 12 Answers ]

Hi, I have an oil forced air furnace, with the fan controlled by a Honeywell L4064 fan limit control. The fan itself is capable of two speeds. I would like to add a fan control centre so that I can control the fan from a switch, hopefully able to select speeds. I gather adding a White-Rogers...

View more questions Search