Ask Experts Questions for FREE Help !
Ask
    ELSTIV305's Avatar
    ELSTIV305 Posts: 2, Reputation: 1
    New Member
     
    #1

    Jul 2, 2008, 01:55 PM
    Washer discharge pipe
    I had gotten a new washer. The main line is 2" and runs under the slab. The 2" line comes up 12" and then T off too a 1 1/2" line with a P trap. The 2" runs straight up for vent pipe.
    When the washer discharges it backs up the 2" vent that is is 8' AFF and around the 1 1/2"
    I have snaked the 2" line and still have trouble. What is my next step?
    Milo Dolezal's Avatar
    Milo Dolezal Posts: 7,192, Reputation: 523
    Plumbing Expert
     
    #2

    Jul 2, 2008, 09:03 PM
    Today's washing machines have powerful pumps that discharge water too quickly for old sewer pipes. Your washer should have 2" P- trap attached to 2" Sanitary "T" and at least 30" of stand pipe. Unless you have this set up, your washer will continue to overflow.
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #3

    Jul 3, 2008, 06:40 AM
    Quote Originally Posted by ELSTIV305
    I had gotten a new washer. The main line is 2" and runs under the slab. The 2" line comes up 12" and then T off too a 1 1/2" line with a P trap. The 2" runs straight up for vent pipe.
    When the washer discharges it backs up the 2" vent that is is 8' AFF and around the 1 1/2"
    I have snaked the 2" line and still have trouble. What is my next step?
    We have had quite a few complaints like yours, especially with new MayTag washers) where the washer pump is too powerful for a 1 1/2" trap and stand pipe. I would increase the trap and standpipe to 2" and install a compression fitting,(see image) on it.
    I have a solution that I've never had a complaint on and one that I had to use on my washer. You close off the stand pipe the washer connects to with a compression fitting,(see image) or I caulked the hose in with rags and sealed it with duct tape. This makes a water tight connection between the washer and the stand piipe. Nothing can leak out or overflow and the force from the pump will send the discharge out into the main drain. While there is some back pressure involved there will not be enough to damage the washer pump. Outside of oversizing the washer trap and standpipe this is about the only solution that I know that works. Good luck, Tom

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Washer discharge pipe 7 feet up wall [ 5 Answers ]

The washer discharge pipe in our rental townhouse is about 7 feet from the floor. We've gone through two washing machines in 2 1/2 months because the washers can't pump the water up that high and something seems to burst in them. Last time the entire basement was flooded. Someone said we could get...

Need washer drain pipe installed, now washer stand pipe is backing up. [ 3 Answers ]

I've had to route my washer drain out of my septic system (drain fields are bad). In the house crawl space the washer pipe 2" pvc came through the floor one bend (elbow) and 3' of travel to the septic cast iron pipe down to the septic tank. I cut into the pvc just past the elbow (maybe 2' past)...

Drain pipe for washer backing up once washer starts to empty what could be causing [ 4 Answers ]

What couild be causing the drain pipe fro washer to back up and spill all over floor behind washer

Disposal discharge tube doesn't reach PVC pipe [ 2 Answers ]

Hi, I'm in the process of installing a new disposal in my kitchen but ran into a bit of a snag when I went to connect the new disposal. I've attached pictures of the old/new disposals along with the pipe configuration under my sink. As you can see from the pictures, the new disposal is smaller...

TP discharge pipe [ 2 Answers ]

Any code requirements, or advantage/disadvantage on the type of pipe used for the water heater TP discharge? My old heater used PVC and that’s what I used on the new heater. I’ve also seen copper used, mostly in new homes, I guess because the length of copper pipe was available.


View more questions Search