Ask Experts Questions for FREE Help !
Ask
    tippysowner's Avatar
    tippysowner Posts: 5, Reputation: 1
    New Member
     
    #1

    Jun 21, 2008, 02:39 PM
    18.5 Briggs Ic Motor Questions on Carb Problems
    Hello I am Jim in Tennessee. I own a yardman Professional series Riding 42" Cut mower and it starts but can't find a manual for it anywhere on how to set the carb. I have emptied all old gas and new gas in it and even 2 new plugs in it and it dies after mowing for less than 3 minutes. Put a new carb kit in it also(diaphragm and springs). I will include the model and serial numbers in this message below this text.

    Model Number=13AS699G088TMO-320420S

    Serial Number=IC177H30128

    Model Number the letter after M in TM might be a D but not sure which.

    Even yardman website can't find the manual. Need It desperately or the instructions on how to set carb to get it working properly.

    Thanks,
    Jim
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #2

    Jun 21, 2008, 05:30 PM
    It's an MTD. Parts & Accessories | Shop & Find Lawn & Garden, Appliance Parts at Sears Parts Direct | SearsPartsDirect.com from Sears will find the model 13AS699G088 .

    If you really want the engine manual, you have to find the engine model #. I'm not going through the diagrams at searspartsdirect to find it. That info is in the service manual which cost $.

    Carb setting is usually:

    Bottom both mixture screws and back out about 1.5 turns. That should get the engine started.

    At low speed adjust the smaller screw so that the engine idles smooth.

    Move the engine to high speed and adjust the larger screw until the engine runs smooth.
    tippysowner's Avatar
    tippysowner Posts: 5, Reputation: 1
    New Member
     
    #3

    Jun 21, 2008, 06:17 PM
    Ty for the help KeepItSimple. I had no idea that sears parts direct would have it.

    Jim from Tennessee.
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #4

    Jun 21, 2008, 07:31 PM
    Lots of stuff here too:

    PDF Manual Web Archive
    MOWERMAN2468's Avatar
    MOWERMAN2468 Posts: 3,214, Reputation: 243
    Ultra Member
     
    #5

    Jun 23, 2008, 04:47 AM
    Is it running yet?
    tippysowner's Avatar
    tippysowner Posts: 5, Reputation: 1
    New Member
     
    #6

    Jun 23, 2008, 08:03 PM
    No the way it acted the last time I tried to start it. Well it runs it just does not stay running for over 3 minutes. If I try to set the adjusment screws on the carb as suggested then it dies while attempting to let the choke off after getting the motor trimmed out. Think it could have a bad float in the carb or water in the gas someway?

    Any help apprecciated.

    Thanks,
    James

    I am not the best Mechanic on mowers.
    MOWERMAN2468's Avatar
    MOWERMAN2468 Posts: 3,214, Reputation: 243
    Ultra Member
     
    #7

    Jun 25, 2008, 05:47 AM
    Absolutely possible for contamination. Also try it with the cap off the fuel tank. If you tear into a carb, clean the entire fuel system. You could also have a blockage in the jets of the carb.
    tippysowner's Avatar
    tippysowner Posts: 5, Reputation: 1
    New Member
     
    #8

    Jun 26, 2008, 03:18 AM
    Ok thanks for all the help. I also have talked to a repair shop locally in person and they said My mower has the solenoid on the carb. They said sound like that is the problem. I will try starting it without the gas cap off after work today.

    Thanks, again,
    James
    wsbraun's Avatar
    wsbraun Posts: 2, Reputation: 1
    New Member
     
    #9

    Jun 26, 2008, 09:57 AM
    I have a b&s twinII 18.5hp will start but will only run for 5 or 10sec. Choke has to be on to run(for 5-10sec). Fuel line is unobstructed. Cleaned fuel pump. Disassembled and cleaned with gas. There was some gunk. Diaphams looked OK. Did not just add fuel.
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #10

    Jun 26, 2008, 12:08 PM
    Gas won't clen the carb. You have to use carb cleaner. Spray can works. You have to pay attention to mixture screws and fuel valve. Clen these thourghly.

    And FWIW carb cleaner can be used as starting fluid. Starting fluid is not recommended for small engines.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Briggs&Stratton Pulsa Jet Carb problems [ 9 Answers ]

I'm having trouble starting an older aerator with a B&S 3.5hp horizontal shaft engine with a Pulsa Jet carb. I've changed diaphragm, and carb-to-fuel tank gasket. It can be started and run on starter fluid, but doesn't seem to pump gas into carburetor. What else to look for?

Briggs 14.5 oil in carb [ 2 Answers ]

I have a rider with a briggs 14.5OHV. It will run for a little bit then oil pours into the carb from a breather I'm guessing? Is the breather bad or do I have bigger problems.

Briggs and stratton carb problems [ 8 Answers ]

I have been having problems with my briggs and stratton 12.5hp motor! The carburator keeps getting too much gas into the float reservoir and gas comes out. I recently purchused a brand new carb and installed it but still seam to get too much gas to the carburator when I go to start it. Could it be...

Oil getting into carb on 16 hp Briggs [ 1 Answers ]

I have a lawn tractor with a 16 hp Briggs engine. It burns oil. I put Lucas oil in and it helped. However the problem is back! There is oil showing up in the air filter. Obviously the engine smokes. What are the possible causes?

Murray Riding (Briggs Motor) carb sputters quits -- too much fuel? [ 11 Answers ]

I have an old Murray riding motor that won't run for more than a minute or two. If I clean the plug, I can get it to start fairly easy but will start to sputter and finally stop after a minute or two. I took the carb off and made sure the float wasn't stuck -- it appeared fine. Running the mower...


View more questions Search