Ask Experts Questions for FREE Help !
Ask
    abruner's Avatar
    abruner Posts: 3, Reputation: 1
    New Member
     
    #1

    Jun 16, 2008, 09:50 AM
    Replacing old electric sockets
    I've moved into a very old house with very old electric wall sockets (one in each room.) Some of them are so worn, anything I plug into them falls out or is very loose which means if it gets kicked it comes right out. Does anyone know how to replace these? The internal wiring is very good, it's just a matter of a replacing the outside plate and tightening it up, but I have no idea how to go about it.

    Name:  DSC00001.JPG
Views: 545
Size:  145.2 KB
    WallyHelps's Avatar
    WallyHelps Posts: 1,018, Reputation: 136
    Ultra Member
     
    #2

    Jun 16, 2008, 11:09 AM
    I can't tell exactly how large the box is, but could you use something like this?
    Any good electrical supply house (not big-box home improvement centers) should be able to help you out regardless if you take a receptacle with you.

    Good luck,
    WallyH
    hkstroud's Avatar
    hkstroud Posts: 11,929, Reputation: 899
    Home Improvement & Construction Expert
     
    #3

    Jun 16, 2008, 09:30 PM
    As Wally said we can't tell how big the box is. For that matter I can't be sure that there is a box. Of course the standard residential today is duplex outlets. Single outlets are available but their straps would probably be made to fit the standard duplex electric box. Remove the outlet and take it to a electric supply house (where electricians by material). You never know. Where are you located? That outlet is rated for 10 amps and 250 volts, not the norm for US residential.
    westnlas's Avatar
    westnlas Posts: 322, Reputation: 25
    Full Member
     
    #4

    Jun 16, 2008, 09:48 PM
    Try "www.hubbell.com" There is an e-catalog for all their parts. I didn't search further, because you know exactly what to look for. Good luck.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #5

    Jun 17, 2008, 05:23 AM
    With power off, to remove the recepticles, remove just enough material to expose the 2 screws, and remove screws completely. Then slide receptacle up or down to get free from behind material. You need that backing so when new receptacle is installed it sits ON the wall, not floating. You don't have to replace with Hubbell.
    westnlas's Avatar
    westnlas Posts: 322, Reputation: 25
    Full Member
     
    #6

    Jun 17, 2008, 02:25 PM
    Actually, they can be replaced with tiger boxes and updated components or anything else you would choose. All you need is a hot wire and a common which seems present in the existing circuits. I was merely pointing out where you might find exact replacements. I would go to Home Depot and buy the cheapest thing I could find that I could make work and stick that in.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Outside electric sockets - no power following rain storm [ 2 Answers ]

Week or so ago I inadvertently left the cover open on the electric socket on the rear of the house. That night we had a storm. Couple days later I plugged something in and discovered - no juice. I tried the socket on the front of the house - no juice. When I checked the circuit breaker box, I...

Sockets arking [ 2 Answers ]

I have changed several outlets in my home,now when I plug in different items they overload my breaker.My outlets have six wires that I'm not sure I have correct. I saw something about a pigtail in a book but I don't rember where. Can anyone help?

One and Three way light sockets [ 2 Answers ]

I have a few three way lamps in the house. I was wondering if I could put a energy saving light bulb in those lamps without causing any danger? The energy saving light bulbs are one way. Thanks for the help, Bryan

Electric Hot Water Heater - replacing anode rod [ 3 Answers ]

What is the procedure for replacing the anode that is screwed into the top of an electric hot water tank? In theory it's supposed to be easily replaced, but in real life getting any fitting unscrewed after many years can be a risky. Any tricks or just brute strength? I haven't change it. I...

Sockets and fixtures [ 1 Answers ]

Hello how many sockets and light fixtures can you run off one breaker I want to install a plug socket and light fixture in a basement room I just finished can I just tap into the light fixture in the other room?


View more questions Search