 |
|
|
 |
New Member
|
|
Jun 14, 2008, 03:36 PM
|
|
Removing frozen bathroom sink valve
Hello,
I'm new to this site.
My question is that I'm trying to replace the water shut off valve in bathroom sink.
It has a compression fitting, but the "nut" is frozen...
Does anyone have any suggestion on how to break the "nut" loose?
Thanks,
Keagan
|
|
 |
Eternal Plumber
|
|
Jun 14, 2008, 04:01 PM
|
|
 Originally Posted by bdshields
Hello,
I'm new to this site.
My question is that I'm trying to replace the water shut off valve in bathroom sink.
It has a compression fitting, but the "nut" is frozen.........
Does anyone have any suggestion on how to break the "nut" loose?
Thanks,
Keagan
If your stop looks like this one,(see image) put a wrench on the stop to keep it from turning and another on the compression nut and back it out counter clockwise. NOTE: If you['re replacing it you don't have to replace the old nut and ferrule. Simply reuse them. Good luck, Tom
|
|
 |
Full Member
|
|
Jun 14, 2008, 04:27 PM
|
|
I am nearly certain that there is a place to put a wrench on the body of the valve to hold it. But if there isn't, grab it with a large pair of channel lock pliers and hold it so you can turn the nut with a wrench. Don't worry about damaging it, you are replacing it anyway. You might even be able to hold it with a pipe wrench. If you absolutely cannot remove it, is there enough room to cut the pipe behind it and still be able to attach a new one. There is a push fitting made for copper that requires no soldering. I think it's called "Gator Grip". If you must cut the pipe, maybe you can install a fitting and attach a new valve. Good luck with it.
|
|
 |
Eternal Plumber
|
|
Jun 14, 2008, 07:32 PM
|
|
There is a push fitting made for copper that requires no soldering. I think it's called "Gator Grip".
LOL! Close westnlasbut no cirgar for you. It's "SHARKBITE" (see image) But you were bang on about removing the angle stop and the "no-solder" fittings. Regards, Tom
|
|
 |
Full Member
|
|
Jun 14, 2008, 07:37 PM
|
|
Thanks for setting me straight. I knew I saw them someplace and even read a bit about them. I am getting a good laugh at myself for getting the name wrong though. Maybe "Gator Grip" was a Florida football term? Ther's so much going on in retirement, I can't keep track. LOL
|
|
 |
Ultra Member
|
|
Jun 14, 2008, 07:54 PM
|
|
I don't think that you would need a shrkbite coupling, just follow Tom's instruction, Thanks.
John
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Leaky Valve under bathroom sink
[ 5 Answers ]
First of all I would like to thank who ever can answer this for me...
The hot water valve under the bathroom sink is leaking from just behind the valve knob... or it could be from the nut behind it... how can I stop it from leaking... everytime I turn the valve on it starts spraying and...
Removing shut off valves under bathroom sink.
[ 3 Answers ]
I had a problem after I insstalled a new sink faucet. I had a small drip coming from the cold water shut off valve below the sink. No matter how I tightened or loosened it, the screw in front and the knob itself, it would still drip slowly. So I figuered I would just replace the valve. I bought a...
Removing old Bathroom Sink Fixture
[ 1 Answers ]
I am trying to remove an old bathroom sink fixture, including the stopper and have run into a problem. I have removed everything except the 5 inch piping used for the drain that connects directly to the u-shaped pipe carrying the water out. I can't remove the washer at the top of this pipe,...
Bathroom sink hot water shut-off valve
[ 6 Answers ]
I live in a house on columns. In following the instructions for removing a bathroom sink faucet I turned the shut-off valves off. The cold side did not run, but I am getting a drip from the hot side... a drop every second or two. I tried shutting off the supply downstairs. But the drip persists....
Bathroom Sink Valve Leak
[ 2 Answers ]
The shut off valves under my bathroom sink have started leaking and I am not sure what to do. The sink has had a tendency to clog lately, and I am not sure if this is related or not. Are there any suggestions on how to repair the dripping valves? Please advise.
View more questions
Search
|