Ask Experts Questions for FREE Help !
Ask
    dave123456789's Avatar
    dave123456789 Posts: 3, Reputation: 1
    New Member
    		  
    #1

    May 28, 2008, 06:56 AM
    No pressure in my ford iveco clutch
    When I engauge my clutch there is no pressure so it get stuck down and can't get it in or out of gear. I changed the slave cylinder and there is no change. The master is working fine so I am unsure of what it could be.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
    		  
    #2

    May 28, 2008, 07:09 AM
    Have you Bled it? Plenty of fluid? How do you know Master is working fine? I had a Ford Van with stick shift and where the clutch master cylinder was mounted, metal got weak and "Flexed", I fabricated what I called a "pressure dispertion plate"? It stopped the flexing and solved the problem, may not be your problem.
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
    		  
    #3

    May 28, 2008, 07:38 AM
    Likely, there's air in the system and it needs to be bled.
    dave123456789's Avatar
    dave123456789 Posts: 3, Reputation: 1
    New Member
    		  
    #4

    May 28, 2008, 07:51 AM
    It has only stopped while the new slave cylinder has been put in and I have bled the system but no change
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
    		  
    #5

    May 28, 2008, 08:02 AM
    It only takes the smallest amount of air for the pedal to go to the floor. It can be a very frustrating experience. Try to use a pressure bleeder.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
    		  
    #6

    May 28, 2008, 09:08 AM
    When slave cylinder was replaced, any rods or mechanisms seemed to all go back in place? Plenty of fluid?
    dave123456789's Avatar
    dave123456789 Posts: 3, Reputation: 1
    New Member
    		  
    #7

    May 28, 2008, 02:16 PM
    Yes all the mechanisms went back in place and I topped up the fluid but there was no change. Have not tried the pressure bleeder.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Ford Explorer low oil pressure reading [ 11 Answers ]

:confused: l have a 2000 ford explorer XLT (4.0 SOHC V6) and the oil pressure has been low during the start up and then pops up to normal levels after driving/idle for few minutes. Here is the run down: 114K miles and have used synthetic oil 10-30 regularly after the 15K mile mark and always...

1995 ford escort wagon ac low pressure port [ 1 Answers ]

I need to know where the low pressure port is located on a 1995 ford escort wagon. Thank you!

98 ford e 350 7.3 no start condition, what should fuel pressure be at head [ 1 Answers ]

My question is what should fuel pressure be at rear of head I have a 98 e350 with a 7.3 and a no start condition, I have changed the relevant sensors and the only thing that I have left is poss. Fuel pressure so I need to know what the fuel pressure should be

Ford Power Stroke 6L loses turbine pressure [ 1 Answers ]

I have a v8 ford 250 power stroke, 2005. I tow a 4000 lb trailer. It worked fine until about 35,000 mile. After that, when climbing and towing the trailer, the turbine pressure would drop from 30 to 10 or 20 lb and the rig would drop from 60 mph to between 40 to 50 mph. The turbine and the EGR have...

Ford 6.0 high pressure turbo boost bypass valve [ 1 Answers ]

I have an 05 f-250 that recently started (after being in storage for the winter) popping the bypass valve for excessive turbo boost the engine is stock and the problem is intermittent the ford dealer just put in the latest pcm that did not help . Can somebody out there help me?

View more questions Search