Ask Experts Questions for FREE Help !
Ask
    galactus's Avatar
    galactus Posts: 2,271, Reputation: 282
    Ultra Member
     
    #1

    May 9, 2008, 05:14 AM
    Volume of semicircular trough wrt angle tilted
    Here is a toughy. ebaines, whatcha think?

    Given a semicircular trough of length L and radius r that is full of water, derive a formula for the amount of water in the trough wrt the angle it is tilted to the horizontal.

    I believe this requires more than one integral for the different scenarios.

    i.e. the top(end tilted up) is partially covered and the top end is not covered.
    ebaines's Avatar
    ebaines Posts: 12,131, Reputation: 1307
    Expert
     
    #2

    May 9, 2008, 06:01 AM
    Galactus - you're idea of fun is definitely twisted! I'll give it a shot and get back.
    galactus's Avatar
    galactus Posts: 2,271, Reputation: 282
    Ultra Member
     
    #3

    May 9, 2008, 10:29 AM
    I know. This problem is a booger. There are various scenarios to consider.

    Are the slices parallel to the water surface? Is the bottom partially covered or not covered? On and on. It'll probably require 3 or 4 different triple integrals.
    ebaines's Avatar
    ebaines Posts: 12,131, Reputation: 1307
    Expert
     
    #4

    May 11, 2008, 01:14 PM
    I don't think it's all that complicated. Take slices parallel to the end cap, integrating the incremental volume of water for each slice depending on the depth at each point along the length of the trough. The depth is equal to R-x* tan(alpha), up to the point where either x = L or x = R/tan(alpha).

    I'm traveling this week, but hope to get you an answer in the next day or so.
    galactus's Avatar
    galactus Posts: 2,271, Reputation: 282
    Ultra Member
     
    #5

    May 14, 2008, 10:42 AM
    Here's something I came up with.

    galactus's Avatar
    galactus Posts: 2,271, Reputation: 282
    Ultra Member
     
    #6

    May 15, 2008, 06:18 PM
    Oops, mistake in the above. That's for a circular, not semi-circular trough. There is no way to edit or delete. Wonder why?



    There are different ways to approach this. And depending on the level of the water, determines our integral.

    The equation for the trough would be

    The equation of the water surface is a plane

    k is determined by the angle the trough is tilted.

    We could slice the water perpendicular to the y-axis and get rectangular cross sections.

    We could slice the water perpendicular to the z-axis and get sections of circles and use polar coordinates.
    ebaines's Avatar
    ebaines Posts: 12,131, Reputation: 1307
    Expert
     
    #7

    May 16, 2008, 06:25 AM
    I don't understand what your integral equation is - are you suggesting the volume of water is not dependent on the length of the trough? Also, for you get , surely that's not right?

    Here's what I've got - I used a coordinate system with x along the length of the trough and y parallel to the end cap. The angle of the trough to the ground is . The depth of the water at any point along the length of the trough is then:

    , and for .

    The cross-section area of the water of depth h is found from:



    Subbing in :



    The volume is then:

    ,

    where
    .

    From this I arrived at:
    For

    and for


    where

    This is admittedly a bit ugly - perhaps there's an elegant way to simplify this expresion which I'm not seeing.
    galactus's Avatar
    galactus Posts: 2,271, Reputation: 282
    Ultra Member
     
    #8

    May 16, 2008, 08:39 AM
    Hey ebaines:

    That one I posted is for a particular scenario. When the water does not touch the other end.

    There are obviously two integrals needed when the water does touch it and that is what you have. That's similar to my workings.

    Very cool, ebaines. You're a 'smart feller'.

    I will post my other solution this afternoon.
    galactus's Avatar
    galactus Posts: 2,271, Reputation: 282
    Ultra Member
     
    #9

    May 16, 2008, 11:38 AM
    Here's what I came up with when the bottom is covered and the top is only partly covered.



    Barring any typos.:)

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Size of wiring trough [ 6 Answers ]

I'm unsure of what size wiring trough to use . I'm coming into the trough from the meter pan with 500 MCM (320 amp single phase service) I'll be coming out to two 200 amp service disconnects and using 3/0 wire. An electrician neighbor of mine recommended a 12" X 12" X 48" trough but the...

Air flow trough orifice [ 1 Answers ]

I would like to find out air volume (cfm) and velocity of air passing through orifice 1/4" diam. At 350psi pressure. Please explain calculation.

Tilted cervix [ 2 Answers ]

Has anyone heard of a dr trying to pull on a tilted cervix to straighten it out. I have a friend who is pregnant and is due November 11 she is 3cm dialated but the dr is waiting because her cervix is tilted. She said he tried to straighten it out by pulling on it. I have never heard of...

Tilted uterus [ 1 Answers ]

Is it harder to hear the baby's heart beat at 10 weeks with a tilted uterus? Kristy


View more questions Search