Ask Me Help Desk

Ask Me Help Desk (https://www.askmehelpdesk.com/forum.php)
-   Home Safety & Security (https://www.askmehelpdesk.com/forumdisplay.php?f=158)
-   -   Changing phone number on Arrowhead Elite v4.1 alarm (https://www.askmehelpdesk.com/showthread.php?t=506523)

  • Sep 10, 2010, 05:44 PM
    rolly10
    Changing phone number on Arrowhead Elite v4.1 alarm
    Alarm has been ringing an old No. . The lady tracked us down, and asked us to switch the No. .
    The type of alarm panel is an Arrowhead Elite V4.1, And the L.E.D. keypad is a V4.0c.
    The trouble is the company that sold us the alarm ten years ago closed, any help finding the location address to change this would be appreciated.
  • Sep 10, 2010, 06:53 PM
    Stratmando

    If being monitored by another company, they will want to program in their receiver phone number, your account, etc, test system.
    Otherwise you should be able to disconnect a Large Phone Jack near the panel, this should disable calling them, but to eleminate the trouble beeps or lights, you will need to disable communications, and telco monitor in Installer Programming.
    :: Arrowhead Alarm Products ::
  • Sep 13, 2010, 02:40 PM
    rolly10
    [thanks for answering, this question has been on my mind for a few weeks, think I'll go the way of pulling out the phone jack.
    Cheers .
  • Sep 13, 2010, 03:34 PM
    Stratmando

    unplugging the jack is one thing and is safe.
    Removing will need re connecting to ensure you don't lose inside phones.
    Inside the Big Jack at Panel(RJ 41X), you need to connect 2 pairs of wires, whatever is on the green to gray, and whichever is on the red and brown, connect together.
    or just unplug jack at panel.
  • Sep 14, 2010, 03:59 PM
    rolly10
    Going to un-plug jack and then we"ll set the alarm into use, It"s been ages since we"ve been able to, so thanks so much for the help.
  • Sep 14, 2010, 06:08 PM
    Stratmando

    You should be fine, may just have to have a trouble light if not able to reprogram.
  • Jul 2, 2012, 12:46 AM
    DJL2323
    Installed an Arrowhead S Lite Alarm but cannot programme it as the default code 000000 will not let me into the set up. What are some possible problems or errors I could have made, the key pad seems to work but will only let me go into the mode that changes the display. Please help.
  • Jul 2, 2012, 05:11 AM
    Stratmando
    DJL, are you getting a Ready Light?
  • Jul 2, 2012, 11:23 AM
    DJL2323
    No the keypad is lit up but there are no lights
  • Jul 2, 2012, 01:40 PM
    Stratmando
    Most come defaulted to work as a basic system, do you have EOL's?
    Any response from the zones?
  • Jul 3, 2012, 12:37 AM
    DJL2323
    The motion sensors are picking up movenment but I can not programme any zones or even set a defult code to work. Yea the EOLs are in each of the motion units but the problem seems to be with the keyboard and that there are no troubleshooting instructions. If something was wrong I would think it should be displaying an error code but haven't had anything come up that would point to any fault
  • Jul 3, 2012, 05:55 AM
    Stratmando
    Power down and hook keypad to Buss Directly, maybe a wiring problem

  • All times are GMT -7. The time now is 10:59 PM.