Ask Me Help Desk

Ask Me Help Desk (https://www.askmehelpdesk.com/forum.php)
-   Tools & Power Equipment (https://www.askmehelpdesk.com/forumdisplay.php?f=334)
-   -   Mtd troubleshooting (https://www.askmehelpdesk.com/showthread.php?t=461421)

  • Mar 30, 2010, 11:51 AM
    Germanyjon
    Mtd troubleshooting
    My Yard Machine manual states I have a 20 amp fuse mounted on the dash panal on the right side. I can't found it anywhere. Any suggestions?
  • Mar 30, 2010, 02:58 PM
    cdad

    You need to examine your wiring harness. It could be a inline fuse that appears anywhere.
  • Mar 30, 2010, 05:31 PM
    DG

    Its by the battery and solenoid,sometimes it curls under the battery base plate.
    Its going to be a spade type fuse/
    Luck
  • Mar 31, 2010, 08:16 AM
    Germanyjon
    Thank you everyone!

    BTW, the battery is dead but when I try to charge it, the charging unit shows it is fully charged. What gives?
  • Mar 31, 2010, 08:29 AM
    DG

    Probably has a dead cell this will show as good but will not put any current out.
  • Mar 31, 2010, 10:09 AM
    Germanyjon

    What does the fused circuit control?
  • Mar 31, 2010, 12:17 PM
    DG

    Cranking,
  • Apr 1, 2010, 11:39 AM
    Germanyjon

    I've put in a new spark plug and battery and refreshed the fuel by 2 gallons. Engine tries to start. Any suggestions?

    Is there a fuel additive that will help? Would spraying ether into the air filter create a problem?
  • Apr 1, 2010, 11:44 AM
    DG

    You could put some sea foam in your fuel.But no either .try spraying carb cleaner in the carb
    This should start it.
    Luck.
  • Apr 1, 2010, 12:07 PM
    Germanyjon

    Is the carb located where the fuel line attaches? If so, I see no way to spray anything it it.
  • Apr 1, 2010, 05:58 PM
    DG

    Take the air filter off then you can spray in there.
  • Apr 2, 2010, 07:17 AM
    Germanyjon

    Thank you. Do you know where the model number is?
  • Apr 2, 2010, 04:07 PM
    DG

    Should be under the seat .
  • Apr 3, 2010, 09:26 AM
    Germanyjon
    I meant engine model number.

    I put the carb cleaner in and it ran until it all was used and then quit. Same for putting fuel in the carb.

    On my last try the engine began to occasionally seize. What does this mean?
  • Apr 3, 2010, 01:07 PM
    jsfocke

    Is there a wire going t the bottom of the carb? If there is you probably are not getting current to it letting the gas go into the engine. Make sure you hear a click when you turn the key on.
  • Apr 4, 2010, 09:51 AM
    Germanyjon
    No wire

    What is the white disk on the fuel line?
  • Apr 4, 2010, 10:54 AM
    DG

    That's the fuel filter,take the bowl off the bottom of the carb,run a wire up through were you took the bolt off that holds the carb on.do not spray carb cleaner on the inside of the carb it has a rubber seat .The engine number will be on the valve cover or the piece of metal covering the muffler

  • All times are GMT -7. The time now is 01:15 AM.