Ask Me Help Desk

Ask Me Help Desk (https://www.askmehelpdesk.com/forum.php)
-   Plumbing (https://www.askmehelpdesk.com/forumdisplay.php?f=259)
-   -   Can't find tub spout that fits copper piping. (https://www.askmehelpdesk.com/showthread.php?t=353602)

  • May 13, 2009, 10:46 PM
    mcw
    Can't find tub spout that fits copper piping.
    Last resort was to come to this site. I've tried to speak to the "experts" at Lowe's and Home Depot but no luck. I purchased an universal tub spout with diverter at Lowe's. The universal tub spout is too small to fit the male copper piping. There's no threads at the end of the copper pipe as well. What size or exact tub spout am I look for? Thank you.
  • May 13, 2009, 11:28 PM
    afaroo
    1 Attachment(s)

    See the images below and one of them may be like yours, Thanks.

    John
  • May 14, 2009, 04:12 AM
    massplumber2008
    MCW:

    Any universal SLIP FIT spout with diverter (#5 above in John's post) should work on this... However, there is a trick or two to make them fit easier... ;)

    Here, you want to DEBUR the end of the copper pipe sticking out of the wall a bit using a file and then if needed use a little silicone grease to grease the pipe end a bit and then spin the spout back and forth until it slips onto the pipe. Once the spout hits the wall tighten the allen screw with an allen wrench and you should be all set.

    Let us know if you have more questions...

    MARK
  • May 14, 2009, 05:33 AM
    speedball1
    If you do not deburr or bevel the end of the copper pipe it will catch on the "O" ring and push it out of its place resulting a leak out the back of the spout every time you draw a bath. Good luck, Tom
  • May 14, 2009, 04:32 PM
    mcw

    I'm not sure that I'm explaining myself properly. The problem is that the old tub spout's nipple extension is large enough to fit around the copper pipe. The new universal tub spout's nipple extension is too small. My middle finger can go into the opening of the old nipple extension but cannot fit into the new one. There's a visual difference between the two extensions as well. Any ideas? Help? Thank you.
  • May 14, 2009, 04:39 PM
    mcw

    Never mind. I called Fergusons and was told that I probably had a 3/4 inch extension not half-inch. I know it's not one inch. I'll go there tomorrow and special order the thing. Thank you for your help.
  • May 14, 2009, 05:23 PM
    massplumber2008
    3/4" extension or a 1/2" brass nipple is my guess..? Sorry... missed the MALE COPPER PIPING part in your post. Since you have threads on the end of the nipple you will need a spout like #1 or #3 in Afaroo's post.

    That should finally resolve this for you.

    Good luck!
  • May 14, 2009, 07:09 PM
    mygirlsdad77
    [QUOTE=mcw;173387 The universal tub spout is too small to fit the male copper piping. There's no threads at the end of the copper pipe as well. .[/QUOTE]

    This is mighty confusing. Do you have a threaded stub out, or just plain copper with no threads? If you could post a couple pics of your setup, we will try our best to help. Please let us know how things work out, or if you would like more help on this.
  • May 14, 2009, 08:43 PM
    afaroo

    Mygirlsdad is correct, MCW please explaian is the pipe coming out of the wall 3/4" with threads at the end and what is the length of the pipe, Thanks.

    Regards,
    John
  • May 14, 2009, 10:09 PM
    mcw

    The circumference of the pipe is 3/4 inch. There are no threads at the end of the pipe. I never measured the length of the copper pipe. I'm sorry for the confusion.
  • May 15, 2009, 03:40 AM
    massplumber2008
    1 Attachment(s)
    Mcw... do you mean the DIAMETER is 3/4"??? Circumference of 3/4" copper tubing is 2 5/8"..so you must mean diameter....??

    If no threads present then this sounds like a 3/4" copper tube (3/4" copper tubing is 7/8" diameter... and 1/2" copper tubing is 5/8" diameter) and you can either order a 3/4" slip on spout OR install a 3/4" x 1/2" sharkbite reducing coupling and a 1/2" sharkbite threaded (MALE) adapter (see picture)and then install these PUSH-FIT fittings (solderless fittings). You might also need a small piece of 1/2"" copper tubing (type L-sold in small pieces at home depot and lowes only). Then you could purchase the 1/2" threaded diverter spout (nose connection type #3 above) and install all this in about 5 minutes (you would also need a copper tubing cutter)... just another option anyway.

    Or, if you can solder fittings on same as above, but use regular copper fittings.

    Anyway, talk to the counter guys at ferguson... see what they can make up for you. They should be able to come up with something that will not require waiting or special ordering... ;) Be sure to know the length of the stub out before you go.

    Good luck!

    MARK
  • May 15, 2009, 08:50 AM
    mcw
    Thank you very much for the options. I'd just assume special order the spout as I'm busy with many other projects in this fixer-up home. I'll be back, I'm sure, with more questions. Thank you again.

    Matthew
  • May 15, 2009, 09:05 AM
    Milo Dolezal

    Mark, I would not recommend Shark Bite fitting for this application as Shark Bit fitting will not hold tight allowing the spout to turn around...
  • May 15, 2009, 10:11 AM
    massplumber2008
    It was just a thought... a little caulk would hold the spout in place, but yeah.. not my first choice for him either!
  • May 15, 2009, 03:19 PM
    mygirlsdad77

    So they do make 3/4 slips spouts? Never seen one. Good to know they exist.

  • All times are GMT -7. The time now is 06:52 AM.