The flange is installed at leaste 1/2 in. off level causing the toilet to rock back and forth.The floor is ceramic tile over concrete.How can this glued in place flange be removed so a new one can be properly installed. Thank you

Hi TP...

You are sure it is the flange that is out of level and not the floor.. right? Have you lifted the toilet and actually confirmed that the flange is the issue? Let me know.

Basically, if there is enough room between the flange and the fitting underground you may be able to cut the old flange out using an INSIDE PIPE CUTTER (see picture) inside a drill and then use a coupling and install a new flange.

Looking down inside the 3" pipe you would need a minimum of 4.5" of pipe to be able to cut the pipe 3" up from the bottom of the pipe and install a coupling. Then you could use a STREET closet flange (hubless) into the coupling to fix issue.

If 4" pipe and you have a minimum of 6" of pipe then you may be able to cut the pipe 4" up from the bottom of the pipe and install a DEEP Twist and set or a set and screw type closet flange that fits inside the pipe itself (see picture). That would work nicely here... IF ENOUGH PIPE.

Most likely there will not be extra pipe length needed in between the fittings, so really need to check the numbers out.

Let me know what you think here...

MARK

Quote:

---

Originally Posted by massplumber2008

Hi TP...

You are sure it is the flange that is out of level and not the floor..right?? Have you lifted the toilet and actually confirmed that the flange is the issue?? Let me know.

Basically, if there is enough room between the flange and the fitting underground you may be able to cut the old flange out using an INSIDE PIPE CUTTER (see picture) inside a drill and then use a coupling and install a new flange.

Looking down inside the 3" pipe you would need a minimum of 4.5" of pipe to be able to cut the pipe 3" up from the bottom of the pipe and install a coupling. Then you could use a STREET closet flange (hubless) into the coupling to fix issue.

If 4" pipe and you have a minimum of 6" of pipe then you may be able to cut the pipe 4" up from the bottom of the pipe and install a DEEP Twist and set or a set and screw type closet flange that fits inside the pipe itself (see picture). That would work nicely here...IF ENOUGH PIPE.

Most likely there will not be extra pipe length needed in between the fittings, so really need to check the numbers out.

Let me know what you think here...

MARK

---

Thank you for your help. I did remove the toilet and the flange is installed as described. The pipe is 3" and startes its bend 4 1/2-4 3/4" below the top of the flange. The 1 1/2" drain from the adjacent bath tub enters the 3" pipe approx. 5 1/2' below the top of the flange.As you indicated, there is not enough extra pipe to make the repairs as suggested. What are my options at this point?

If you have a STREET FLANGE, i.e. a flange that fits INSIDE a fitting then you may be able to use a RAM BIT tool (see picture below... it is a pipe reamer/remover... sold only at plumbing supply house, most likely) to remove the old flange. Here, you would remove the old metal ring around the top of flange (use aviation snips or grinder if needed... wear goggles) and then using a sawzall with an 8" bimetal sawzall blade cut the plastic flange flush with the floor. Then you would set the ram bit in a drill, set it inside the remaining part of the flange and remove it down to the hub.

Check out this link on the pipe hog (similar to the ram bit):

Pipe Hog PVC-ABS Fitting Reamer

If your flange is a REGULAR FLANGE and you have no room as discussed then you would be best to cut off the old metal ring and cut the pipe down and then see if you can fit an OATEY 3" twist and set flange (or similar). Here, the pipe must be flush with the floor and then the twist and set flange gets set into the 3" pipe and is twisted down until fit is tight. You may need to cut this flange down an inch or two.

Check it out at:

http://www.oatey.com/apps/catalog/in...Set_Flange.pdf


Let me know what you think here...

MARK