Hi I have a 1991 honda civic dx that won't start

I just changed the whole starter including the offset gear that is attached and changed the 50a fuse that is under the hood no response everything comes on in the car but starter doesn't respond at all I can push start the car but in dire need of fixing it

Did you bypass the solenoid? I assume there is no cranking? Do you have a safety switch on the column?

Your civic is manual I assume, there is a "safety" switch under the dash top of the clutch that has a plunger in it. See if that piece is broke (a hole you will feel top of the clutch assy) if this is missing a sub fix can be to put a bolt in this hole or just ho9ld the button in to start until you can get part.

P.S. after 2 weeks we just found this same one ourselves tonight!

Hey but you know what they still have the plunger in the part but the clutch isn't hitting it in all the way think there might be something wrong with the part still or now my clutch

Well Paulie, Did you get the fix yet as to your issue? Could be that plunger needs to be changed, mine had actually broke and fell out. Glad to hear you got it to crank though!

OK so I drove the car and it ran just fine but I killed it now it won't start any more tried to push it and start it but it tried to but just didn't start fulepump is working but I have no idea what to do I let it cool off and went out and it started right up drove it home killed it and tried to restart but nothing what could be the problem

Main relay. Read the FAQ.

Quote:

---

Originally Posted by CroCivic91

Main relay. Read the FAQ.

---

I'm having a similar problem with a 89 CRX Si. They symptom is the car won't crank, but will run if push started. I disassembled the ignition switch, but it looked OK. I pulled the starter and had it tested, also OK. I checked the clutch switch and it seems to be intact. I pushed in the plunger, but still no start. Now I've pulled the main relay. I looks OK too, though I haven't tested it. My question is, can a bad main relay demonstrate these sysmptoms?

LOL Again I can qoute CroCivic... read the faq... see if you have codes in your system. Could be any number of things, as I was recently notified by Haynes books, Hondas have any number of things that will "kill" the start on this car, and as I learned the hard way the books just don't cover them all. First thing first though, see if you have codes, could be a code in there that can point the right direction! :)

Turns out it was the clutch switch after all. I took another look at it and was able to depress it fully by hand, after which the car started fine. Now I just have to figure out how to replace it!

Quote:

---

Originally Posted by Jarg

Turns out it was the clutch switch after all. I took another look at it and was able to depress it fully by hand, after which the car started fine. Now I just have to figure out how to replace it!

---

If you do not find a cheap solution, you can also try to bypass it with a wire. It purpose is to disallow the car to be started if the clutch is not pressed in (safety measure). If you bypass it, you won't have to press the clutch to start the car. It's only a switch after all.

Quote:

---

Originally Posted by CroCivic91

If you do not find a cheap solution, you can also try to bypass it with a wire. It purpose is to disallow the car to be started if the clutch is not pressed in (safety measure). If you bypass it, you won't have to press the clutch to start the car. It's only a switch after all.

---

I thought about that. The main problem is getting to the darn thing. I can feel it by reaching up the clutch pedal, but I haven't been able to see it! Also, I may not have to mess with the switch at all. I think there may be a rubber stopper of some part that is, or was attached to the pedal assembly, and I'm speculating that it came off, and therefore the plunfer on the clutch swtich is not being pushed in far enough when I press the clutch. I'm going to take another look at it when I get a chance.

I just stuck a screw in it don't have to fit just have a big head not to long or small and has been working just fine for me or you sure the plunger is on and if not this will work for now if the plunger is still intact don't put screw

Quote:

---

Originally Posted by PAULIE

i just stuck a screw in it dont have to fit just have a big head not to long or small and has been working just fine for me or you sure the plunger is on and if not this will work for now if the plunger is still intact dont put screw

---

Holy crap, can't you put some dots and commas in that sentence?

Glad to see someone is getting good use of our learnings! And CroCivic, thanks for the laugh!! LOL:D

By the way, for those of you trying this "fix" for the clutch, I did learn "body panel clips" for ford work perfectly when inserted with the flad head side on the switch side of the clutch pedal,also they are only $1.44 for 4 @ any parts house :cool: