Hi There!

I have a 2nd floor fiberglass shower.

The drain was leaking.

I cut a hole through the ceiling.

It's a 2 inch brass drain with a compression fitting.

I got the old drain out OK.

Bought a new Sioux Chief replacement drain.

My questions are a follows:

Isn't there a tool I can obtain to take out the compression nut that sits over the compression washer instead of crossing 2 screwdrivers to unloosen the
Compression nut? If there is what is it's name and where can I get one.
Menards and Home Depot do not have one.

When I put in the new drain how tight do I tighten the compression nut
Over the compression washer?

Also when I tighten the slip nut on the underside of the drain to the underside
Of the shower there is about a 4 inch circle cut around the drain as the shower
Base sits on top of 3/4 inch plywood to ensure the shower floor is sturdy and level.
Isn't there an offset slip nut wrench you can get bigger than 2 inches to actually fit
Snugly around the slip nut so it is easily removed. Once again the largest wrench
I could find was 2 inches so when I tried to grab the slip nut because it wasn't offset
It wouldn't grab it.

I got lucky and was able to latch on to one of the teats with a vise grip and
With the 2 screw drivers it all came off.

Any help or information given would be appreciated.

Regards,

David Nars

Considering the cramped work-space limitations you face, you would do better to return the drain you bought and replace the drain body with a "Davke 2000" No-Caulk drain assembly.

The Davke was designed for just the scenario you describe -- It tightens up much like a garbage disposal shoe, eliminating the need to crank down on a large nut.

As for the tool needed to tighten the inner ring, the drain assembly should come with one just under the grid top.

Do yourself a favor, when installing the rubber ring, coat it liberally with clear silicone caulk, this will make seating the rubber ring all the way to the bottom of the drain assembly much easier -- Silicone caulk is very slippery.

And if a bit of pipe protrudes past the rubber ring and the brass compression ring, you can cut it flush internally with a dremel tool and corrugated cut-off wheel.

Good Luck!

I like the answer growler gave and would love to be able to do that. Where would I get that shower drain to stock my truck? I have never seen or heard of one.
The brass no-caulk drain that was removed is probably the best option [next to that special drain] to use. Lowe's sells a drain that has no nut on the bottom. It tightens from the top. On a second floor install that may better suit you. But, why is the drain leaking? Does the shower floor flex? You may have to support the fiberglass so the repair will not leak.

Quote:

---

I like the answer growler gave and would love to be able to do that. Where would I get that shower drain to stock my truck? I have never seen or heard of one.

---

Try contacting the inventor to see if it is stocked locally at any of your supply houses.

Quote:

---

Originally Posted by doug238

i like the answer growler gave and would love to be able to do that. where would i get that shower drain to stock my truck? i have never seen or heard of one.
the brass no-caulk drain that was removed is probably the best option [next to that special drain] to use. lowes sells a drain that has no nut on the bottom. it tightens from the top. on a second floor install that may better suit you. but, why is the drain leaking? does the shower floor flex? you may have to support the fiberglass so the repair will not leak.

---

Growler gave you good advice but if you can't locate a Davke 2000 shower drain consider a WingTite shower drain, (see image), which uses the same principle and can be purchased at most stores. Good luck, Tom

Growler, thanks. I contacted the company. Tom, I have not seen one of those either. My experience has been in the pensacola area from 1973 till 1987 then the orlando area for 15 years and not the atlanta metro area for 6 years. I may need to get out more.

Not an answer, but a repeat of the first question really: is there such a thing as an offset or right-angle wrench to use on the no-caulk shower drain ring that can be used in tight spaces?

My problem is similar to that of the topic starter. I ordered a WingTite drain but still have to get the leaking one out, or at least loosen it.

I have 2 separate layers of drywall (ceiling and recessed pipe cover) and a old deck supporting the shower pan to cut through. Plus lots of other pipes in the way. I should be able to cut some of the deck away, but definitely not enough to allow for a full wrench or pair of pliers to be put in place.

Yes there is. I think home depot now carries it. It is a large socket, plastic, that is used on the nut under the typicall shower drain or the large nut sink basket strainer. It fits in a 5 or 6 inch hole

If you can't locate a wrench I take a hammer and cold chisel and whack the retaining nut counterclockwise until I can take it off by hand. Good luck, Tom

Quote:

---

Originally Posted by speedball1

If you can't locate a wrench I take a hammer and cold chisel and whack the retaining nut counterclockwise until I can take it off by hand. Good luck, Tom

---

Hell, I just cut the big ol' nut off with my trusty Dremel tool and a reinforced cut-off wheel.:D

Two cuts and you can pry it off - Then again, you *DO* need to be very careful you don't slip and accidentally cut into the shower base.

OK, now how are you going to reinstall it? Lowe's carries a shower drain that fits snug up to the bottom of the shower and all pieces thread in and tighten from the top. It is pvc and glues on.

Quote:

---

Originally Posted by doug238

yes there is. i think home depot now carries it. it is a large socket, plastic, that is used on the nut under the typicall shower drain or the large nut sink basket strainer. it fits in a 5 or 6 inch hole

---

Quote:

---

Originally Posted by iamgrowler

Hell, I just cut the big ol' nut off with my trusty Dremel tool and a reinforced cut-off wheel.:D

Two cuts and you can pry it off - Then again, you *DO* need to be very careful you don't slip and accidentally cut into the shower base.

---

Quote:

---

Originally Posted by speedball1

If you can't locate a wrench I take a hammer and cold chisel and whack the retaining nut counterclockwise until I can take it off by hand. Good luck, Tom

---

Thanks guys, very helpful. I checked Lowe's and a Bill's Hardware (specialized store here in the DC area), but no luck. Will check out Home Depot tomorrow but might end up whacking/cutting that nut. Planned on replacing the old drain for a WingTite drain anyway.

Probably have to resolve some flexing of the shower pan as well. I doubt if it was properly set in a mortar base. Oh, the joys of homeownership...

Thank you for the info on the Davke shower drain, after many hours of searching for a fix to my leaking fiberglass shower drain with no space for a wrench this will work, and the owner of Davke shower drains was great, thanks again. Jim in NY.

Hi Jim and welcome to The Plumbing Page at AMHD.com. You're responding to a 6 year old dead threads s. Please check the date before you post. Thanks for the update. Hope all is well. Tom

Massplumber referred me to bulldogdraintool.com. They have wrench that works on the compression nut on no caulk drains.