I want to finish a basement(new construction) that has cinderblock walls. However I do not want to use sheetrock. Are there other alternatives?

Hi, bmay!

Are the cinder block walls coated with anything at all at the present time, or are they just the bare blocks?

Thanks!

You could skim the walls with drywall compound 2 times first coat is a will bee a bit ruff let it dry sand it re coat it with a thin coat it should go in smoother then texture it prime and paint if you do this if the wall moves it will crack if it leaks the mud will fall off if I was doing it I would use 2 x 2 and foam insolation and then sheetrock it

Using drywall compound directly on the cinder block would not be a good idea because all cider block absorbs moisture and would deteriorate the compound over time.
If you wanted to skim the walls with something, use a mortar mix, then paint.

lol sabre drywall compound = smoother morter mix = ruffer both absorb moisture if the wall is dry and painted drywall compound is fine I own a drywall co in wi and we have to do this very often in stair wells we don't get call backs

Quote:

---

Originally Posted by arby808

lol sabre drywall compound = smoother morter mix = ruffer both absorb moisture if the wall is dry and painted drywall compound is fine I own a drywall co in wi and we have to do this very often in stair wells we dont get call backs

---

Lol arby, I own a drwall and constrction company in Pa, if you are only using it in stairwells, that's one thing. But to use it on exterior cider walls, it will absorb moisture and deteriorate the compound.

Only if they are wet I own a drywall and home inspection co in wi if the walls are dry you will have no problem if the walls are wet or damp you will have problems with anything you put on them

I have been doing drywall for over 30 years and agree with the people who indicate you will eventually have problems with drywall compound. I would NOT recommend it as a long term finish, as it will deteriorate, crack, peel,. and generally make a BIG mess.

You did not indicate the degree to which you would like to go. Specifically, you didn't indicate if you were averse to putting up 2x2 studs and using alternative interior finishing techniques. If you are open to studding the wall(s), then virtually any finish is open to you. Prior to installing any studs be sure the walls are sealed with products such as DRYLOK (or comparable alternatives). Then install the studs, insulate (if desired), vapor seal and then use paneling or other desired internal finish product. I've seen and used "wafer board" that is stained too.

Alternatively, you could use Faux stone (Manufactured stone veneers) or a mortar stucco. With the stucco, you can have the mortar colored so that the walls would not require painting when finished. Of course they could be painted later if desired. The stucco also affords several options in "texture". It can be finished smooth, swirled, brushed, or give it a venitian plaster look. (... A smooth finish is very challenging to achieve and should likely be left to professionals.) These types of finish would be very durable.

Finally, if you don't mind the concrete block look, but want a finish, you can simply paint the walls with a product like DRYLOK (or comparable). I have a finished basement room with dropped ceilings. Two of it's walls are exterior walls (made with concrete block). They are painted with a product like DRYLOK. The two walls "finishing" the room are drywall. However, they could have been paneling or any other suitable wall finish.

By the way: DRYLOK usually comes white, but can be tinted any color you like (mine is yellow). This also expands when being applied to fill the pours in the concrete block and the mortar holding them. You will usually require two coats.

Lasco panels are available at places like Lowe's or Home Depot type stores. They are fiberglass sheets with a grained finish. Easy to clean. You need a 1/4" hammer drill bit to drill the holes for the expansion rivit used to install them. There is no food for mold with these.