Ask Experts Questions for FREE Help !
Ask
    JungleCat's Avatar
    JungleCat Posts: 27, Reputation: 1
    New Member
     
    #1

    Sep 1, 2009, 04:39 PM
    Trouble with sanding discs
    I am making log furniture and using both black and decker and porta cable 5" disc sanders. The sanding discs will not stay on the pads and keep on falling off. I tried using blue line sialink disc rolls which stick to the discs as well as hook and loop sanding disc but nothing stays on for long. I have changed the pads on both sanders with the same results.
    Any suggestions what I can use to do the job without this problem?

    Tanxs


    Bob
    Scleros's Avatar
    Scleros Posts: 2,165, Reputation: 262
    Hardware Expert
     
    #2

    Sep 1, 2009, 05:54 PM
    Try sanding stars, flutter sheets, or mop.

    Source:
    Klingspor's Woodworking Shop
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #3

    Sep 1, 2009, 06:08 PM

    Hook and Loop disks are not going to hold up. You also have to replace the hook side once and a while. High pressure kills them. Use them only for finishing operations.

    For cheap prices on sandpaper try Welcome to Supergrit.com

    I ordered some hook and loop sheets from them for various grits and the loops on the back of the sandpaper varied in strength depending on the grit used.

    They also have the hook material which I should have ordered.

    Another type of adhesive that you can use essentially comes as a solid tube. You use it on the backing plate and then attach the disk. This is the method used in industrial disc sanders. None of this convienience stuff. Hook and loop and pressure sensitive, is just that convienience.

    If you need more help, holler.
    JungleCat's Avatar
    JungleCat Posts: 27, Reputation: 1
    New Member
     
    #4

    Sep 1, 2009, 07:48 PM

    Is there any abrasive I could use on the disc sanders? That is the tool that I need for this type of work.


    Bob
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #5

    Sep 1, 2009, 09:34 PM

    Here is an abrasive selection sheet. http://www.mscmarket.com/PDFS/Catalo...ccessories.pdf

    You really need the PSA (Pressure Sensitive Adhesive) and backing plates.

    Fine, high speed sanding would probably best be done with an ir powered sander.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Painting Prep - Sanding [ 2 Answers ]

I recently purchased a home and am in the process of repainting. I've patched all the screw and nail holes in the walls. I want to fully sand the walls before putting on the primer since the current paint job has lots of drip marks and such. Question 1) What grit should I use for the final prep...

Peel and stick sanding pads [ 2 Answers ]

I have a porta cable and dewalt 5" orbital sander. The sand paper that are hoop and loop just do not stay attached with the felt backing. As I am using them on log furniture I need a peel and stick type sand paper however I have been told that I have to change the pads to use them. When I asked...

Alternative to sanding drywall joints? [ 13 Answers ]

I'm gettin' pressured to put up another wall in my basement, and my wife says she saw on diynetwork (TV show) a guy showing that you can mud the seams as you normally would, then let it dry only 1-2 hours then come back with a wet blade and skim them... instead of sanding them: No sanding...

Sanding Corian countertop [ 1 Answers ]

Where can I find Corian refinishing kit?


View more questions Search