 |
|
|
 |
Junior Member
|
|
Feb 4, 2009, 01:41 PM
|
|
Energy hydrolics log splitter
Ihave a energy hydrolics 20 ton log spilter about 20 years old.
The engine is a 5 hp tecumseh engine that will not run.
It will run for a bit then die. It ran fine before until I replaced the carb.
Mower_Man
|
|
 |
Uber Member
|
|
Feb 4, 2009, 02:02 PM
|
|
A couple of questions:
1) Is the gas tank metal?
2) Did you set the high and low speed mixture screws separately?
3) If it has a primer bulb, is that system intact?
|
|
 |
Junior Member
|
|
Feb 4, 2009, 03:24 PM
|
|
No it is plastic
4 cycle
Has choke.
I NEED HELP!! Mower_Man
|
|
 |
Home Repair & Remodeling Expert
|
|
Feb 5, 2009, 07:23 PM
|
|
Just curious, if it ran fine why did you replace the carb? Still have the old carb? See where I am going with this?
|
|
 |
Ultra Member
|
|
Feb 6, 2009, 02:56 AM
|
|
Mower man plastic gas tanks cause more moisture in the gas then metal. I didn't believe that until I had a plastic tank in a shed. It heated up more and cooled to cause more condensation check gas. Just wanted to add that little diddy.
ballengerb1 and KeepItSimpleStupid is one a good track here.
Just popped in for the plastic gas tank comment.
Signed 21 Boat
If I Helped To Answer Your Question Please Rate My Answer
|
|
 |
Junior Member
|
|
Feb 6, 2009, 08:25 AM
|
|
When I moved, it hit something and broke the carb,where it attaches,so I replaced it.
|
|
 |
Home Repair & Remodeling Expert
|
|
Feb 6, 2009, 08:35 AM
|
|
Did you install a brand new OEM carb with new gaskets? Double check you throttle and choke linkage for binding and proper travel.
|
|
 |
Junior Member
|
|
Feb 6, 2009, 10:25 AM
|
|
I got a used oem tecumseh carb. It will fire and then will not start,throttle works,new gaskets(OEM)
Mower_Man
|
|
 |
Uber Member
|
|
Feb 6, 2009, 12:12 PM
|
|
Take apart and clean the carb then.
That should be a big light bulb.
|
|
 |
Junior Member
|
|
Feb 6, 2009, 12:22 PM
|
|
The carb I got had been taken apart and cleaned,it did and help at all.
Thanks for all of your time and help,KISS,ballengerb121boat. Thanks!
Signed, Mower_Man.
I need to know what elese could cause it to fire then not to run?
Maby the vaves?
Reply soon? M_M
|
|
 |
Uber Member
|
|
Feb 6, 2009, 12:27 PM
|
|
How long is "run for a bit"?
|
|
 |
Junior Member
|
|
Feb 6, 2009, 12:32 PM
|
|
Very short, like for 1 minate or so.
Signed, Mower_Man
|
|
 |
Uber Member
|
|
Feb 6, 2009, 12:50 PM
|
|
It really does sound like a fuel issue. Bad fuel. Not enough octane. Not using the mid-grade. Not using a stabilizer like stabil-when stored. Water in the gas tank. Gas cap vent plugged (operate without the cap on to test). Bad fuel filter.
Carb not adjusted right. Low and high speed not adjuated separately. Dirty air cleaner. Rust or other debris in the fuel system.
|
|
 |
Junior Member
|
|
Feb 7, 2009, 12:02 PM
|
|
I will try it and see.
Thank all of you! KISS,ballengerb1 and the rest of you.
Signed Mower_Man
|
|
 |
Junior Member
|
|
Feb 8, 2009, 05:12 PM
|
|
I ended up changing the engine,I needed to use it an I put a 6 hp tecumseh power sport(go kart engine) with a throttle control.
I will mess with the old motor some other day.
The year of the machine is 1980 and it was $799.00 back then.
Thanks for the help.- I will post back when I get it to run.
Mower_Man.
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Log splitter
[ 3 Answers ]
I have inherited a duerr log splitter from my father in law who is now in the nursing home with dementia and I would like to change the oil filter on it. I have the part # from manual which is #723-0405 filter element. The model # is 424/lcd/22 (249-623-003). Could you give me a number & name...
Potential Energy- Bonding Energy
[ 1 Answers ]
Question: The net potential energy between two ions (e.g. Na+ andCl-) can be
Represented as follows:
EN =EA+ER = -A/r +B/rn
(a) Calculate the bonding energy E0 in terms of the A, B, and n
...
Log Splitter
[ 4 Answers ]
I have lost power on my log splitter.
Help with log splitter
[ 4 Answers ]
I'm attempting to build a log splitter. I finally got it all assembled and it works great but seems very slow. I have a briggs 5 hp motor, Haldex 11 gpm pump, cross 2500 psi valve and a lion 4x24 cylinder. I think the problem is the pump. Although it is a 2 stage it starts on the first stage and...
View more questions
Search
|