Hi, I have a project where I would like to pull information from multiple parameter queries using cells in a worksheet. My VB skills are not great, but I have been able to use code found on other forums to pull from a single query. The problem is when I try to add another query to my code it only pulls from the first query.

I am attaching two sets of code below… the first is the working code that pulls form a single query, the second is me adding code to try and pull from an additional query (does not work). The code includes turning off calculations while the import is being done and then turning them back on once the import is complete.

If anyone is able to help me figure out how to make this work it would be a huge lifesaver.

FIRST SET OF CODE, WORKS PULLING IN A SINGLE PARAMETER QUERY:

Sub GoToManual()

Dim xlCalc As XlCalculation
xlCalc = Application.Calculation
Application.Calculation = xlCalculationManual
On Error Go to CalcBack

Dim MyDatabase As DAO.Database
Dim MyQueryDef As DAO.QueryDef
Dim MyRecordset As DAO.Recordset
Dim I As Integer

Set MyDatabase = DBEngine.OpenDatabase _
("H:\Dashboard\ManifestData.mdb")
Set MyQueryDef = MyDatabase.QueryDefs("ManifestAnalysis")

With MyQueryDef
.Parameters("[Origin:]") = Range("D5").Value
End With

Set MyRecordset = MyQueryDef.OpenRecordset

Sheets("All Data - CY").Select
ActiveSheet.Range("A6:K999999").ClearContents

ActiveSheet.Range("A2").CopyFromRecordset MyRecordset

For i = 1 To MyRecordset.Fields.Count
ActiveSheet.Cells(1, i).Value = MyRecordset.Fields(i - 1).Name
Next i

MsgBox "The station data has been added to the workbook. Please hit OK and allow time for the calcualtions to process."

Application.Calculation = xlCalc
Exit Sub
CalcBack:
Application.Calculation = xlCalc
End Sub

SECOND SET OF CODE, MEANT TO PULL IN TWO PARAMETER QUERIES BUT ONLY PULLS IN ONE:

Sub GoToManual()

Dim xlCalc As XlCalculation
xlCalc = Application.Calculation
Application.Calculation = xlCalculationManual
On Error Go to CalcBack

Dim MyDatabase As DAO.Database
Dim MyQueryDef As DAO.QueryDef
Dim MyRecordset As DAO.Recordset
Dim I As Integer

Set MyDatabase = DBEngine.OpenDatabase _
("

Application.Calculation = xlCalc
Exit Sub
CalcBack:
Application.Calculation = xlCalc
End Sub

SECOND SET OF CODE, MEANT TO PULL IN TWO PARAMETER QUERIES BUT ONLY PULLS IN ONE:

Sub GoToManual()

Dim xlCalc As XlCalculation
xlCalc = Application.Calculation
Application.Calculation = xlCalculationManual
On Error GoTo CalcBack

Dim MyDatabase As DAO.Database
Dim MyQueryDef As DAO.QueryDef
Dim MyRecordset As DAO.Recordset
Dim i As Integer

Set MyDatabase = DBEngine.OpenDatabase _
(")
Set MyQueryDef = MyDatabase.QueryDefs(")
Set MyQueryDef = MyDatabase.QueryDefs(")

With MyQueryDef
.Parameters("[Origin:]")

With MyQueryDef
.Parameters("D5") = Range("All Data - CY").Value
End With

Set MyRecordset = MyQueryDef.OpenRecordset

Sheets("A6:K999999").Select
ActiveSheet.Range("A2").CopyFromRecordset MyRecordset

For I = 1 To MyRecordset.Fields.Count
ActiveSheet.Cells(1, I).Value = MyRecordset.Fields(I - 1).Name
Next I

Set MyDatabase = DBEngine.OpenDatabase _
(").ClearContents

ActiveSheet.Range(")
Set MyQueryDef = MyDatabase.QueryDefs("ManifestAnalysisTwo").CopyFr omRecordset MyRecordset

For i = 1 To MyRecordset.Fields.Count
ActiveSheet.Cells(1, i).Value = MyRecordset.Fields(i - 1).Name
Next i

Set MyDatabase = DBEngine.OpenDatabase _
("[Origin:]")
Set MyQueryDef = MyDatabase.QueryDefs("D5")

With MyQueryDef
.Parameters("Station Data - CY") = Range("A6:K999999").Value
End With

Set MyRecordset = MyQueryDef.OpenRecordset

Sheets("A2").Select
ActiveSheet.Range("The station data has been added to the workbook. Please hit OK and allow time for the calcualtions to process."

Application.Calculation = xlCalc
Exit Sub
CalcBack:
Application.Calculation = xlCalc
End Sub

You appear to have used the same Origin value from D5. That's fine, except the second part you aren't ON the same sheet you started from. So you do need to include a sheet reference to make sure the D5 is taken from the correct sheet. What I did was was NOT move to the second sheet, instead I showed you how to send commands to the CY sheet without "selecting it" first.

Next, you didn't change anything in the second second set of code regarding where the data is inserted. Cells(1, i) equals A1 then first time through the for/next loop, then B1, C1, etc. So you're putting the values into row1. The second time through the loop you need to put the values in row2.

So, I'd tweak your macro down as shown to retain the origin D5 value and put the second query results in row 2.


The tweaks may be wrong, but they're meant to get you looking at your code in terms of what it DOES to your sheet, where it puts things. You can't "clear contents" twice and wonder where half the data went, you cleared it! You can't put data in the same place twice and wonder where half the data is... you wrote over the top of it. You must change something the second/third times through to make sure your new data is being added below the first set.

Ah ha! Thank you so much!

I was clearing and pasting the different data sets into different sheets so that wasn't an issue.

You hit the nail on the head when you said "You appear to have used the same Origin value from D5. That's fine, except the second part you aren't ON the same sheet you started from". I left the origin sheet so when it came time to pass the parameter to the second query it was pulling from the wrong sheet.

The issue was fixed by changing:

With MyQueryDef
.Parameters("[Origin:]") = Range("D5").Value
End With

to:

With MyQueryDef
.Parameters("[Origin:]") = Sheets("Welcome").Range("D5").Value
End With

Thank you JB for your help. I never would have thought of that.