I just installed a new submersible pump in my aerator tank. I had checked the air pressure in the pressure tank and it was 35 psi. I have a 30-50 pressure switch. After turning power on the pump turns on but then turns off quickly after pressure has only risen to about 40psi. When using faucets etc. and pressure drops pump starts to turn on and off again quickly. I feel there is no water coming from pressure tank. When I try and lift pressure tank it is very light. Anyone have an idea why water is not going into tank? Thanks
I am totally confused. In your first post which I have copied above, you said that you installed a submersible pump in your aerator tank.
What is an aerator tank? And why would you put a pump in it?
You also said the tank is very light.
Now you say in your second post that there is water in the tank and ask how do you get it out.
I don't know what you are doing but I think there are some things you need to know. Now this is going to be long but if I can take the time to key it in, you can take the time to read it.
1. Well switches are adjustable. The most common settings are 30-50 and 40-60. You say you have a 30-50 switch. That just means the switch is or is suppose to be set to come on at 30 and go off at 50. If you had a 40-60 switch it would be the same switch, just set to come on at 40 and go off at 60. Perhaps your switch is not set properly.
2. There are two types of tanks. There are pressure tanks and there are bladder tanks. The true pressure tank is just a sealed tank, empty except for the air in it. Pressure tanks are galvanized to prevent rust. A bladder tank has a rubber bladder inside. Since the water is pumped into the bladder there is not need to galvanize it. Bladder tanks are always painted.
3. It helps to know how a pressure tank works in order to understand what is happening with your bladder tank.
4. As stated a pressure tank is just an empty, sealed, galvanized tank. When water is pumped into it it compresses the air trapped inside. You also need to know that you cannot compress water. You can only compress air. When you fill this sealed tank to approximately 1/3 water (2/3 air) the compressed air will provide 40 lbs of pressure on the water. When filled to approximately 2/3 water and 1/3 air the compressed air will provide 60 lbs. of pressure on the water. This is where the 40-60 pressures come form.
All this would be just wonderful except for one thing. Water absorbs air, especially air under pressure. That means that as you use this tank the water keeps absorbing the air. That means that you have to fill the tank with more water to reach the 40 lbs. cut on pressure and since there is less air you reach the 60 lbs. cut off pressure quicker. Eventually using the smallest amount of water causes the pressure to drop to the 40 lbs. cut on pressure and pumping in the smallest amount of water causes the pressure to jump to the 60lbs cut off pressure. This is known as being "water logged" and causes the pump to "short cycle". When this happen you have to empty the tank, let more air in and start over.
5. Someone invented the bladder tank. This is just a steel or fiberglass tank with a rubber bladder in side. The water is pumped into the bladder. As the bladder expands it compressed the air between it and the tank. Having the bladder prevents the water from absorbing the air. Having the bladder also lets you put additional air in the tank. By putting additional air in the tank you reach the minimum cut on pressure sooner. You don't have to use 1/3 of the tank volume to reach the minimum pressure. Usually only takes a few gallons. The air pressure of a empty bladder tank should be 2 lbs. less than the cut on pressure of the well switch. This is call the pre-charge pressure. With the pre-charge pressure properly set to 2 lbs. less than the cut on pressure, the pump will come on just before you run out of water. So the bladder tank functions just like the pressure tank except you can add additional air and the bladder prevents the air being absorbed by the water.
The problem with bladder tanks is that the bladder can rupture. When that happens it begins to function just like a pressure tank. Eventually the air in the tank is absorbed by the water and the pump begins to short cycle.
With all this in mind tell us what you have, what you are doing and why.