Ask Experts Questions for FREE Help !
Ask
    1966Daniel's Avatar
    1966Daniel Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Jul 11, 2012, 07:16 PM
    I convert my dryer to LP but I can not adjust the flame
    I Convert my Frigidare Dryer to LP, I opened the window totally, but the flame is still yellow.
    How can I fix it?
    ma0641's Avatar
    ma0641 Posts: 15,675, Reputation: 1012
    Uber Member
    		  
    #2

    Jul 11, 2012, 09:28 PM
    Did you adjust both the orifice and the regulator?
    drtom4444's Avatar
    drtom4444 Posts: 3,282, Reputation: 145
    Ultra Member
    		  
    #3

    Jul 12, 2012, 09:52 AM
    Look at these manuals: https://dl.dropbox.com/u/8010163/Fri...r%20Models.pdf
    https://dl.dropbox.com/u/8010163/Fri...e%20Manual.pdf
    https://dl.dropbox.com/u/8010163/Fri...ontrols%20.pdf
    There is a way to adjust the flame on the dryer. You are going to have to look closely at the valve to see how to do this or close down the supply some.
    1966Daniel's Avatar
    1966Daniel Posts: 3, Reputation: 1
    New Member
    		  
    #4

    Jul 12, 2012, 05:28 PM
    Yes I change the orifice and opened regulator at maximum
    1966Daniel's Avatar
    1966Daniel Posts: 3, Reputation: 1
    New Member
    		  
    #5

    Jul 12, 2012, 05:30 PM
    Quote Originally Posted by drtom4444 View Post
    Look at these manuals: https://dl.dropbox.com/u/8010163/Fri...r%20Models.pdf
    https://dl.dropbox.com/u/8010163/Fri...e%20Manual.pdf
    https://dl.dropbox.com/u/8010163/Fri...ontrols%20.pdf
    There is a way to adjust the flame on the dryer. You are going to have to look closely at the valve to see how to do this or close down the supply some.
    Thank you for the manual and for the tip - I will try it
    drtom4444's Avatar
    drtom4444 Posts: 3,282, Reputation: 145
    Ultra Member
    		  
    #6

    Jul 12, 2012, 09:31 PM
    The spring pressure on the regulator is increased and the orifice is smaller for LP. On some regulators there is a cap on top that is turned upside down for LP in order to increase spring pressure.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Kenmore 90 Series dryer does not adjust temperatures [ 0 Answers ]

We have a dryer that seems to only work on the permanent cycle. I was told that I had to clean the limit switches and clean out the flow where the lint my go. How do I do this.

Flame behind dryer drum [ 3 Answers ]

Have a fridigair dryer #FGR231AS4 is it normal to see flames behind drum(through holes) when looking through front? There on the bottom laft side.

Gas Dryer Flame will not light [ 1 Answers ]

Whirlpool LGR5636PQO Cleaned exhaust; good air flow Replaced igniter and flame sensor Still no flame? Please advise next items to check or replace

Gas dryer flame [ 1 Answers ]

How to adjust kenmore gas dryer flame height

Dryer won't keep flame on. [ 2 Answers ]

When the dryer turns on the igniter heats up and the flame lights but after a few seconds the flame goes out. I replaced the flame sensor but the same thing still happens. There is some sort of sensor on the heating tube but on Appliance Parts Pros.com Discount Appliance Parts – Appliance Repair...

View more questions Search