Ask Experts Questions for FREE Help !
Ask
    Tagnar's Avatar
    Tagnar Posts: 1, Reputation: 1
    New Member
     
    #1

    Jan 17, 2012, 09:57 AM
    Camry 1993 won't crank when hot
    Have a 1993 Toyota Camry - Cranks and starts fine when cold. Let it run for a bit and turn it off - and it won't crank at all for about 20 - 30 minutes (No clicks no grinds, no whirl, nothing), Lights and internal controls all come on fine. Replaced starter and solonid, and starter relay module - with no effect on the problem. Tried starting in Neutral, giggling keys, all the silly stuff that one does when you think it's an ignition switch or neutral switch to no avail. Seems to be a number of folks out there who have had this particular issue (or very similar) - but no definitive resolution.

    Appreciate the help.
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,758, Reputation: 5596
    Uber Member
     
    #2

    Jan 17, 2012, 10:35 AM
    Clean all grounds. Since the starter motor grounds through the mounting bolts, ensure they are clean and free of corrosion. My gut is that the problem is with the heat soaked starter motor (high resistance). Consider installing an additional ground or a starter heat shield. If the problem persists, you may need to install an OEM starter. Toyota rebuilts are superior to aftermarket starters. They are more expensive but much more reliable. My dad is a Toyota man and this has been his experience.

    kitch428, our Toyota trained tech, may have additional suggestions.
    CaptainRich's Avatar
    CaptainRich Posts: 4,490, Reputation: 537
    Cars & Trucks Expert
     
    #3

    Jan 17, 2012, 01:30 PM
    A non-powered test light and a schematic can help fault trace this to where ever the problem is.
    Let me know if you want the schematics.
    Like TxGreaseMonkey says, check the basics first and let us know what you find.
    kitch428's Avatar
    kitch428 Posts: 1,429, Reputation: 152
    Ultra Member
     
    #4

    Jan 17, 2012, 05:14 PM
    You seem like an intelligent person, Tagnar. To me in this case nothing beats a volt meter. (DVOM)
    What I like to do is this:
    Run a jumper long enough from the starter solenoid wire connector disconnected from the starter, to your DVOM.
    Place the meter right on the windshield glass.
    Ground the meter, set to volts, now hit the key to crank just when the problem is happening.
    If you see 12V, then the starter is getting it's supply to at least 'click' the solenoid.
    The rest is in chassis grounds like was mentioned.
    If you bought an aftermarket starter, I'm guessing the problem is there.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

97 toyota camry crank no start [ 3 Answers ]

I have a 97 toyota camry. It's a crank no start. The pump doesn't prime in the on position. I've already replaced the cam and crank shaft position sensors. Tried the ECm on another car and it works good. Any advice would help. Thanks

Why will my 1993 honda civic not crank after it gets hot? [ 7 Answers ]

It runs fine until it gets hot and then it will turn over but not crank. Its getting fuel and spark. I've changed the fuel main relay, the ignition modual. Help!

1993 honda crank sensor location [ 3 Answers ]

1993 Honda civic ex 2 door automatic. I was driving down the road and my car shuts off. Before all this my car has been misfiring. The car turns over but acts like its out of gas. My gas is going threw so its not my pump. Im not getting any spark threw my spark plugs. I replaced though coil and...

My 1993 honda want crank what could it be? [ 1 Answers ]

My fuel pump want come on but if I hot wire it will come on what could it be ?

1993 camry tried everything almost [ 1 Answers ]

My 1993 toyota camry will not start. Will turn over but is getting no fire. Have tried module, distributor, and fuel pump. What's next? Can someone help me?


View more questions Search