Ask Experts Questions for FREE Help !
Ask
    wetmat's Avatar
    wetmat Posts: 4, Reputation: 1
    New Member
     
    #1

    Nov 22, 2011, 11:33 AM
    Appliances
    My kenmore elite gas dryer model 110 75922401 ignites but doesn't stay on long enough to dry the clothes. Please advise what the problem may be and hopefully a solution. Thank you
    ma0641's Avatar
    ma0641 Posts: 15,675, Reputation: 1012
    Uber Member
     
    #2

    Nov 22, 2011, 03:03 PM
    Doesn't stay on long enough or the clothes aren't dry at the end of the cycle? Check the vent where it exits the house. Open? How is the air flow and when was the last time you cleaned the vent line out. I did one for a customer last week and pulled a half a bucket of wet lint out of a 15 ft. line. Lint screen clean? The most common drying issue is from a blocked vent line.
    drtom4444's Avatar
    drtom4444 Posts: 3,282, Reputation: 145
    Ultra Member
     
    #3

    Nov 23, 2011, 01:09 AM

    You will have to clean the drier out thoroughly. Every air duct will have to be removed and scraped and washed out to remove baked on lint deposits which is like concrete lining. This will burn so the manufacturer has installed the safeties to keep from having a house fire. Driers were the number one cause of fires at one time. Look at: http://www.youtube.com/watch?v=MMP7BW1lLs4 to see how. Also: http://www.youtube.com/watch?v=iBiRw-KElC4 ; http://www.youtube.com/watch?v=yFTZGgVisCI
    When you finish cleaning the drier it is best to also replace the belt, too, because you do not want to have to disassemble it again, and if the belt is over two years old you should replace it.

    Note that on most of the videos it does not show them washing out the parts, but this is important because it's the only way to really get the parts clean, just don't get motor wet or the capacitor if it has one. Vacuum out motor. I would move the drier out to your garage to have plenty of space to work. You also want to check your vent and clean it, also. The job is really easier than it sounds. There is no shortcut that will work; it has to be cleaned well. Before you re-assemble it make sure to use white lithium grease (high-temp grease) and grease all bearings. Just vacuuming out the dryer a little does little good. You also want to check the vent and clean it out. When you are done you will have a new dryer and it will dry like new again. You want to clean it like this every two years or every year with many children. DrTom4444

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Appliances [ 2 Answers ]

How do I get a wire diagram of Kenmore 300.110.28332700/washer? Tried the internet not doing any good. BOB, Aug

Appliances [ 1 Answers ]

I am trying to figure out a solution to my problem my kenmore washer filled up with water about an hour later I came back to unload my laundry lifted the top & my clothes were still sitting in water so all I know is that the washer filled with water & that was how it stayed

Appliances [ 0 Answers ]

Ice maker Sears Galaxy Fridge, just hooked up water line, Ice maker works fine, but No Water? What do I need to do to get it to work? Thanks))

GE Appliances [ 1 Answers ]

I have a GE top freezer refrigerator model # PTS25SHSSS I can not get the controls panel lights to come on. After reading the trouble shooting tips it refers to a possible solution as replace the fuse….but it fails to point out where the fuse is located. Their will be a $70.00 service change. ...


View more questions Search