Ask Experts Questions for FREE Help !
Ask
    donnareed's Avatar
    donnareed Posts: 3, Reputation: 1
    New Member
     
    #1

    Jun 27, 2009, 12:48 PM
    Replacing carpeted stairs with wood treads.
    We have replaced our carpet with laminate, but when the carpet was removed from the stairs there is very rough plywood in place, with 36" treads that do not reach the walls... 1/4 to 1/2 " gap on each side, and two triangular landing treads as well. We have decided NOT to put laminate on stairs, but need advice as to how best to cope with the circumstances, as most replacement treads come with a bullnose, making it difficult to envision how to run molding down the sides to come around the bullnose.
    Attached Images
       
    creahands's Avatar
    creahands Posts: 2,854, Reputation: 195
    Ultra Member
     
    #2

    Jun 28, 2009, 05:14 AM

    Stairs where built from bottom up.

    Solution#1 Best way
    Have a stair company install professional stairs.

    Solution #2
    Measure height of each riser.The measurement should be the same for all.

    Remove plywood treads and risers starting at top and working to bottom. Do not remove supports for treads and risers.

    Starting at bottom, glue and nail new riser to supports. Cut 1/16'' less than opening.

    Glue and nail tread to supports and riser. Allow 1'' from face of riser to bullnose. Cut read 1/16'' less than opening.

    Mount nailer on tread in line with next riser support.

    Build stairs in this manner to top.

    Save pie shaped plywood treads to use as templets.

    Solution #3 The worst
    Cut plywood treads flush with existing risers

    Install new risers and treads 1/16''less than opening

    Top step will be 1 5/8'' higher then floor. This will create a tripping edge.

    Bottom step to floor will be 1 5/8'' higher. Also a tripping condition

    I would personally go for option #1

    Good luck

    Chuck
    hkstroud's Avatar
    hkstroud Posts: 11,929, Reputation: 899
    Home Improvement & Construction Expert
     
    #3

    Jun 28, 2009, 07:42 AM

    Cut a fake stringer as shown below. Remove existing plywood treads. Cover existing risers with 1/4 plywood of same species of wood as treads will be. Use construction adhesive to secure riser covers and nail at very end only.
    Install fake stringer. Install new wood treads to fit between fake stringers. Cut to fit tight. Note that you appear to have 3/4 plywood treads currently. Most purchased tread material is 1" thick. That will make 1/4 difference at top. You may be able to mitigate that by lowering top tread by 1/4" and second tread from top by 1/8". Note also that one present tread appears to be 1/2". You will have to install blocking to the wall on the right hand side where stairs make turn. The risers will not meet at that point.

    After removing existing treads you will probably have to install nailing block to esisting stringers so that you have something to nail new treads to after installing fake stringer.

    Fake stringer can be made from plywood of same species, backed by filler strips and veniered on top edge if run is 8' or less.
    Attached Images
     

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Ouside wood stairs [ 1 Answers ]

Where is rot most likely to occur on outdoor wood stairs?

Rotting wood stairs [ 2 Answers ]

Rot is often found where in a set of outdoor wood stairs

Rot on outdoor wood stairs [ 3 Answers ]

Where is the most likely place to find rot on wood stairs?

Wood stairs [ 6 Answers ]

Rot is often found in a set of outdoor stairs. A. at the handrail B. at the bottom of the stringer C. at the tread D. at the top step

Replacing rotten wood floor foundation [ 16 Answers ]

We have an old cabin which we need to repair. Under existing bylaws we would not be able to replace this cabin in its existing waterfront location so repair is the only option. Originally the cabin sat 1 foot above ground on cement pads. Over the years the cabin sunk into the ground which has...


View more questions Search