Ask Experts Questions for FREE Help !
Ask
    mam209's Avatar
    mam209 Posts: 4, Reputation: 1
    New Member
    		  
    #1

    Mar 18, 2009, 04:51 PM
    Bryant furnace cycling on and off
    Thanks for taking your time to read this post! I have a Bryant natural gas furnace model 383KAV036070 that is about 7 years old. It started working sporadically about a week ago. I replaced the thermostat with no luck. It seems that it is reading a trouble code of 34. It will start up and ignite for a few seconds then cut out. It repeats a few times then nothing. The ignitor was replaced about a year ago. I read something in another post that suggests that it might be a flame sensor that needs cleaning. I am not sure if that applies to my problem or not. Any help would be greatly appreciated!
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #2

    Mar 18, 2009, 05:18 PM
    Flame sensor
    Attached Images
      
    KC13's Avatar
    KC13 Posts: 2,556, Reputation: 99
    Ultra Member
    		  
    #3

    Mar 18, 2009, 07:14 PM
    Cha-ching! Another victory for a poster; another dividend for hvac1000! You're probably well covered here... :)
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #4

    Mar 18, 2009, 07:40 PM
    The thrill is not gone!
    Attached Images
     
    KC13's Avatar
    KC13 Posts: 2,556, Reputation: 99
    Ultra Member
    		  
    #5

    Mar 19, 2009, 03:58 AM
    Hey! How many more pictures of me do you have, and where did you get them?:D
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #6

    Mar 19, 2009, 05:06 AM
    I promised not to tell.
    Attached Images
     
    KC13's Avatar
    KC13 Posts: 2,556, Reputation: 99
    Ultra Member
    		  
    #7

    Mar 20, 2009, 03:34 AM
    Got any naked pictures of your wife? No? Want to buy some?:p:D;)
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Bryant furnace cycling on and off [ 6 Answers ]

I have a Bryant gas furnace, model# 310AAV048135. It comes on, runs for a couple minutes then shuts off while the blower still runs. I am getting a fault code of 33, which indicates several things according to the label on the device. Earlier in the summer, I was having a similar problem when...

Bryant furnace short cycling [ 4 Answers ]

I have a Bryant 80 furnace , had the ignitor replaced in November. Since then the furnace will power up, ignitor and burners will go and then when the blower turns on the burners go out, the blower will go for about 90 seconds and then shut down. It will do this repeatedly sometimes as many as 30...

Bryant AC blower fan motor "quick" cycling [ 11 Answers ]

While running in AC mode or fan ON mode the blower fan keeps cycling on/off contiuously for on off periods from less than a second to several minutes. I figured the motor was overheated (bad windings) so I replaced the motor and capacitor with poor results. It seems to run longer but contiues to...

Bryant furnace keeps cycling on [ 2 Answers ]

I have a Bryant Legacy plus 90 furnace that is about 2 & 1/2 years old. The furnace will kick on and run till the temp on the thermostat is reached, it then shuts down but will immediately start back up again and continue to cycle like this 5 or 6 times until I adjust the thermostat down a degree...

Furnace cycling [ 2 Answers ]

My newer energy efficient furnace cycles every 10 minutes about, I have a new one story home that is very well insulated.

View more questions Search