 |
|
|
 |
New Member
|
|
Dec 17, 2008, 08:13 PM
|
|
SHower Diverter covering removal
I have an older home and I believe the original shower/Tub and taps. I need to replace the shower diverter which is in the wall - PULL for shower PUSH for spout. The thing is I cannot figure out how ot get into it. The crome ring on the outside just spins and apears to have not opening. The button in the middle comes off (unscrews) but the appears to be no place on the stem or beside it to lossen anything off. Any ideas? Rabby.
|
|
 |
Home Repair & Remodeling Expert
|
|
Dec 17, 2008, 08:46 PM
|
|
Can you see a brand name or logo anywhere, is sure doesn't look like a Moen.
|
|
 |
Eternal Plumber
|
|
Dec 18, 2008, 07:38 AM
|
|
The face plate behind the knob should turn out counterclockwise. There should be a retaining nut behind that. Good luck, Tom
|
|
 |
New Member
|
|
Dec 18, 2008, 07:02 PM
|
|
I have tried turning the outer ring counter clockwise, but it just turns never loosens. I have looked for any little hidden screw or tension release point, but found none. I can't find any brand name - but yes it's probably not moen. Anyway if you can think of anything else please do - I'll keep looking at it but nothing turns up then I'm going to have to replace the whole thing I suppose, which right now would really bite. Cheers.Rab
|
|
 |
Ultra Member
|
|
Dec 18, 2008, 07:41 PM
|
|
When you get the button in the middle of the push / pull stem out did you not see a screw or a hex head bolt that might unscrew?
Also have you tried to slip a thin knife blade under the escutcheon ( The ring against the wall.) and against the tile on both sides at a 180 degree angle, then try to pull the escutcheon forward, slipping it along a little at a time. Not sure this is the way to get into it but worth a try.
Hope it helps.
|
|
 |
Eternal Plumber
|
|
Dec 20, 2008, 06:31 AM
|
|
#4 Dec 18, 2008, 09:02 PM
Rabby
New Member Join Date: Dec 2008
Posts: 2
I have tried turning the outer ring counter clockwise, but it just turns never loosens.
If the outer ring's threaded then your turning it the wrong way. Clockwise will tighten it. Turn it out counterclockwise. Good luck, Tom
|
|
 |
Ultra Member
|
|
Dec 20, 2008, 05:38 PM
|
|
I would like to thank Rabby for letting everyone know if we hepled him with his problem, that makes you really want to dig into it and see if we can solve problems like his.
|
|
 |
Plumbing Expert
|
|
Dec 20, 2008, 05:43 PM
|
|
Yep, the more input from asker the better, makes us more excited to help.
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Shower diverter stem removal
[ 8 Answers ]
I have an unknown brand shower diverter. It's a knob that sits between the hot and cold knob. All three have a knurled end and the stem appears to be made of brass. The stem on the diverter has been "loose" for some type and squeaks when you turn it. Recently, more water now comes from the spigot...
Shower diverter stem removal
[ 1 Answers ]
After I get the knob and bonnet off how do I get the stem off? I've already stripped the darn thing and am frustrated.
Asbestos siding removal/covering
[ 5 Answers ]
I have just purchased a home in Norfolk VA that has asbestos siding. I would like to find out if I can remove it, and replace with Certianteed siding panels, or can I place the panels directly on top of the original asbestos.
View more questions
Search
|