|
|
|
|
New Member
|
|
Feb 20, 2006, 11:08 AM
|
|
Stem Placement
We are replacing the stems on the hot/cold faucets of our 3 handle tub/shower. We have tried placing the stems facing many different directions, but still we can not get the faucets to turn on and off properly. What are we doing wrong? No directions came with the Danco 3S-9H/C stems.
Any help greatly appreciated!
Thanks
Daisy
|
|
|
New Member
|
|
Feb 20, 2006, 03:05 PM
|
|
Tom,
We believe it is a Delta model 2653 faucet, but not coompletely sure. We night have the hot water working, but the cold water runs full blast no matter how I place the stem and extension it seems. Any ideas?
Thanks
Daisy
|
|
|
Eternal Plumber
|
|
Feb 20, 2006, 04:12 PM
|
|
Originally Posted by Daisy57454
Tom,
We believe it is a Delta model 2653 faucet, but not coompletely sure. We night have the hot water working, but the cold water runs full blast no matter how I place the stem and extension it seems. Any ideas?
Thanks
Daisy
Turn off the water to the valve and pull the cold water stem assembly. Check around the seat for any crud that may be down there. Good luck. Tom
|
|
|
New Member
|
|
Feb 21, 2006, 12:16 PM
|
|
Tom,
I have checked everything, but cold water still does not turn all the way off. Seems er a getting closer, but it still doesn't work right. The hot water works great. I don't know what I could have done differently between the two, any ideas?
Thanks
Daisy
|
|
|
Eternal Plumber
|
|
Feb 21, 2006, 04:02 PM
|
|
Originally Posted by Daisy57454
Tom,
I have checked everything, but cold water still does not turn all the way off. Seems er a getting closer, but it still doesn't work right. The hot water works great. I don't know what I could have done differently between the two, any ideas?
Thanks
Daisy
Daisy,
If the stem assembly works on the hot water side then you have the correct part. Pull the cold water stem and check the valve for any trash that may be caught down there preventing the stem assembly from seating. If everything's cleare aqnd the swtem still won't shut off the water then turn it back in as faulty. Good luck, Tom
|
|
|
New Member
|
|
Feb 11, 2009, 04:51 PM
|
|
Hi Daisy -
After messing around with one of these for the first time today, I finally got it to work right by replacing the new spring (supplied with a new stem I bought - possibly unnecessarily) with the old spring. My version of this kit was made by Delta, and the replacement spring was simply too short to apply enough tension on the new rubber seat. Hope this helps.
John
Correction - the kit was made for Delta by Danco.
J
|
|
|
Ultra Member
|
|
Feb 11, 2009, 11:42 PM
|
|
Hi Daisy,
Follow Tom's advice, and also for identifying the parts, see the link below, Thanks.
John
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Toolbar placement
[ 3 Answers ]
I feel ridiculous. Somehow I managed to move the toolbar (clock, LAN settings, virus protection on the right; short cuts like IE, FOXfire, etc. on the left) from the bottom of my computer screen, around to the right, and then to the top of my screen and I can't seem to move it back. There must be...
Trap Placement
[ 5 Answers ]
I am working on remodeling my basement and have many issues to contend with. The first is the trap for my tub drain on the first floor is well below the floor joists and I would like to raise it up to be able to have a relatively normal ceiling height in the basement. I have been reading that the...
Diverter Stem
[ 1 Answers ]
I am replacing seats and stems in tub/shower. The old one is Sterling--the new faucet set it a PricePfister. The PF diverter stem doesn't fit into the seat (the hot and cold stems do). Can I go to another size diverter with PF?
Placement testing
[ 1 Answers ]
I am currently teaching in a homeschool enivronment. I am looking for a test(s) in reading and math to show mastery of skills for 1,2,and 3rd grades. Any suggestions?? Thanks drseuss
Stem replacement
[ 3 Answers ]
I replaced the stems in the handles of my bathtub faucet. The cold is fine but the hot water leaks where it is screwed into the pipe. Why? I used plumbers dope on the threads and all the washers and O rings are in place (was done same as the cold) why is it still leaking? Very frustrating. It...
View more questions
Search
|