|
|
|
|
Junior Member
|
|
Feb 3, 2014, 05:34 AM
|
|
Can't get crt monitor to work with acer aspire.
Hi folks
Can't get sony e500 crt monitor to work with acer aspire desktop PC, win 7.
At boot up I see "starting windows" etc then a permanent blank screen. PC works fine with the thin screen monitor.
I can't easily get the monitor [very heavy] and the pc to an internet connection although I am online with another pc.
Any ideas appreciated.
|
|
|
Senior Member
|
|
Feb 3, 2014, 09:40 AM
|
|
Have you tried starting in safe mode? If your PC is set to start the graphics in a resolution that the crt cannot handle, as soon as the video drivers are loaded (after the starting windows screen) the crt may not be able to handle it. It could be the resolution or even the Hz setting (if your thin monitor happens to be 120Hz forget it on the crt). If you can get it into safe mode, you can adjust the graphics to 60Hz and a resolution more appropriate for the crt (closer to 4x3). Safe mode, as well as the start screen, run with default graphics settings, that's why the safe mode screens icons and windows are so huge.
|
|
|
Junior Member
|
|
Feb 3, 2014, 09:51 AM
|
|
tried that and its ok in safe mode . but still not in normal mode. i set resolution to 800 by 600 [actually it already was set to that]
cant see how to change hz though
pressed "identify" monitor and it did nothing i could see
win 7
Thanks
|
|
|
Junior Member
|
|
Feb 3, 2014, 10:57 AM
|
|
see above too
setting are now 64. OK hz / 60 hz
12by 1024
cant find a setting for 4x3 [as u suggest]
|
|
|
Internet Research Expert
|
|
Feb 3, 2014, 11:58 AM
|
|
You need to be in full windows mode to make changes like that as when you are in "safe mode" you only have access to default drivers. You should be able to do it with a full bootup. Then tell windows what you want to do with the monitor once it is working.
|
|
|
Junior Member
|
|
Feb 3, 2014, 12:51 PM
|
|
OK but I'm new to win 7. can you please say how I tell that to windows as i was just there and couldn't see anythin useful . and what exactly should i tell it
Thanks
|
|
|
Internet Research Expert
|
|
Feb 3, 2014, 02:27 PM
|
|
Try right click on your desktop and choose personalize. Then choose display. Then choose change display settings. See if the monitor appears there.
|
|
|
Junior Member
|
|
Feb 3, 2014, 02:33 PM
|
|
Yes I did that but of coarse it's the flat one [monitor] that shows up as I had to connect that to run PC normally. I need to kjnow what setting to set even though they are not appropriate fot this monitor
|
|
|
Internet Research Expert
|
|
Feb 3, 2014, 03:30 PM
|
|
What type of video card are you running? Usually in the video card settings you can add a monitor and either "mirror" or "extend" what you are using to view.
Mirror creates a copy of the desktop and displays it the same on both.
Extend actually extends the physical desktop and you can drag things between them.
|
|
|
Junior Member
|
|
Feb 4, 2014, 01:53 AM
|
|
Its onboard , can't see any setting for it
|
|
|
Senior Member
|
|
Feb 4, 2014, 09:04 AM
|
|
4x3 is just a descriptor of the older standard screen size just as 9x16 is for wide screen. When your in the display settings and you change the resolutions you will see the picture of the monitor change from wide to more squarish depending on what settings you choose. Maybe look through the bios for some kind of setting that might help. It's so long since I played with a CRT monitor I'm a little lost, but I can't remember a time when I couldn't swap between them just by plugging it in.
|
|
|
Junior Member
|
|
Feb 4, 2014, 10:00 AM
|
|
That's not helping much, I need some more specific info
Thanks though
|
|
|
Expert
|
|
Feb 4, 2014, 10:18 AM
|
|
|
|
|
Junior Member
|
|
Feb 4, 2014, 10:26 AM
|
|
Its not a laptop. Looked but not appropriate to this
Thabnks
|
|
|
Uber Member
|
|
Feb 5, 2014, 06:57 AM
|
|
Laptop or desktop the procedure is the same... A laptop is just like a desktop with smaller parts packaged in such a way that you can fold it and carry it with you.
|
|
|
Junior Member
|
|
Feb 5, 2014, 09:30 AM
|
|
This doesn't apply to mine, I simply want to make the monitor work as the sole monitor
"Turn on the laptop. Look for the shift or function key combination. This is listed in the manual but also often listed on the keyboard. Holding the key combination will alternate between showing the video on the laptop screen, the monitor or both."
|
|
|
Expert
|
|
Feb 5, 2014, 10:07 AM
|
|
Are you using special connection lines or older ones that came with the monitor?
|
|
|
Junior Member
|
|
Feb 5, 2014, 10:36 AM
|
|
Standard one that's often part of a monitor
|
|
|
Expert
|
|
Feb 5, 2014, 11:27 AM
|
|
And does this cable match perfectly with your tower?
|
|
|
Junior Member
|
|
Feb 5, 2014, 11:39 AM
|
|
Yes, and monitor works OK in safe mode
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Acer Aspire Battery
[ 6 Answers ]
I have an Acer Aspire 5517 laptop. Every so often I notice the blue battery status light turns amber although it's continuously plugged in. When I check the charge level in the system tray I see that it's around 97% charged. It continues to charge until fully charged and the amber light returns to...
Acer aspire 1413
[ 1 Answers ]
Hello all
Can someone please help. I am trying to recoverer my acer aspire 1413 however when I put in the second recovery disk I get a message that states (cannot open image file X:\images\60ea1012.ghs. I suspect my disc is faulty.
Please help
Paulw1200
Acer aspire one.
[ 5 Answers ]
Hey folks,first,happy new year to you all!!
OK,just got an acer aspire one,what a nightmare! It came with mcafee security,so I got rid of that and installed avast,then the problems came,the thing will not work at all,I've got all my icons on desktop but nothing works,I deleated avast but its...
View more questions
Search
|