Search:
Type: Posts; User: Stratmando
Search:
Search took 0.28 seconds; generated 4 minute(s) ago.
-
In addition, Most always, Remove Light kit, Remove Blades, then the screws, Rarely you may find one where you press in a spring loaded button/nub, then lift over opposing nubs on other side.
-
I would identify what each color wire does.
If no separate ground wire, may be intended to be grounded to frame.
Feel it should have more wires
Tail
Stop
Right
Left
Ground
Scratching my...
-
I would verify All your service wires are tite from Meter Can to Main Panel(s), Do turn Off Power, Can be corroded or Burnt connections. Burnt or corroded Buss. Any Junctions.
-
Good Point Donf, If GFI, one way to check is look for the loss of neutral as well, as GFI's when they trip, removes the Neutral as well as the Hot.
Plug Extension Cord in known good outlet so the...
-
Try this:
https://www.uplink.com/our-products/gps-vehicle-tracking/
-
Try this:
https://www.wikihow.com/Transform-Your-15-Pin-(Gameport)-Microsoft-Sidewinder-Precision-Pro-Into-a-USB-Joystick
-
Centrifugal switch may be the issue, Maybe just the contacts. I take it you are talking about the Start Button?
-
Rereading, it may just be the 1 circuit. If you have no meter to test and reseting doesn't help. Swap wire from another 20 amp breaker.
-
If you did all that, would hope you have the Service Manual. If Not, it is a good Investment, Can save a lot of Time and Money. Good Luck. None of what you did should have affected timing. How's your...
-
See if you have 240 volts at the panel, or see if any 240 Volt stuff works. Look at the wiring outside your house, and visually follow the 3 wires to the pole and where they attach too. If the...
-
Sound like she was starting a Pillow fight, Be happy it wasn't bricks or stones. Pillows don't hurt too bad. Looking for a Reaction,
-
It will help reduce voltage drop.
-
If the Fan control switch is on the Fan, wire may have pulled out of fan switch, fan switch may be bad, or capacitor issue.
-
#12 may be correct depending on Watts?
-
Control Panel/Printer/click or right click the printer, see what's printing, Delete Documents in Que. Or very similar. Good luck
-
Poster never mentioned Watts. Many/Most are 240 Volts on a 30 Amp 2 Pole Breaker.
15 Amp Breaker(s) should have tripped. 15 Amps @ 240 Volts is 2880 Watts.
15 X 240 = 2880.
At least the wire is...
-
Stupid question, still in forward gear?
-
You don't have to remove or unplug Microwave to try on a different circuit, a Troubleshooter may remove microwave wire from breaker, then place wire on another Breaker. Swap temporarily so you are...
-
-
Above, or try this:
https://www.google.com/search?q=water+valve+tool&sourceid=ie7&rls=com.microsoft:en-US:IE-Address&ie=&oe=
-
Do you have a particular issue? Can maybe help with that.
-
Don't know, If not printed on it, I would Google Noma Thermostat, then Images, compare photos, or go to eBay, Amazon, other, and search Noma Thermostats, yours may show up? Good Luck
-
You can control 2 or more locations with Elk Electronics WSV2 Electrically controlled 1" Valves, switch 1, the other, or both, add a Network controller, or other device to remotely control on and off...
-
https://dynamiccontrols.com/sites/default/files/2018-05/SHARK%20PMA_PMB_PMC%20Installation%20Manual%20Iss%207.pdf
-
You didn't get all the parts, Google a schematic for it, or if you know where another is, you will want to see what else is connected, like Safeties , May have to jumper some connections.
Throttle...
-
I would turn on lights and look for voltage with a Test light, Identify it as Tail light, or write all colors down and Function next to it.
Remove lenses from both Old and new lights, will tell a...
-
Steely Dan, Las Vegas, Mid 70's
-
There are places that rebuild Battery packs. If able to solder, you may buy the cells themselves and change out. Manufacturers use different methods for charging, 3rd terminal many times is for...
-
I'm wondering if they have a Water Heater that requires a 30 Amp Circuit, but is on a pair of #12's. May never know since I saw no reply to your answer.
-
Many Batteries and Chargers seem to have 3 Connections, Believe the third may be used to sense Heat. At least what it looks like when you change the Internal Batteries.
-
If files are lost and you don't plan on Recovering them(Professional), Then you may be able to hit F11 repeatedly or similar at Start up, It may be Restored to Factory Fresh from a Hidden Partition...
-
Milo, How about Stiebel and Titan? seem Popular in South Florida.
I am a Long Time Electrician, Installed Many. I am not Convinced they are Better Either.
They used to have a High failure Rate, and...
-
Or leave the 3/0, Install a 150 Amp Breaker, (need to do load calculations)call it a day, neutral is commonly a size smaller, as the Neutral carries the difference of the 2 Main Hots. If Black phase...
-
I wired one of my customers AC so if any Doors(could add windows, But they NEVER open) were open more that 5 Minutes it will shut off AC, so they are not Air Conditioning the Outside. Also, if Heat...
-
AND to the sides of the box. Good Luck
-
Just match up the uF(Microfarads), and the Voltage, Replacement can have a higher voltage, Be accurate on the uF. May have 3 terminals, pay attention to where the wires are connected, If it has 3...
-
Whoever does the Backsplash, especially if it Is Marble or Granite for them to cut up to the sides of the box, and so the 2 screws can be inserted. See some who cut openings screws will not go in or...
-
Try new Batteries, or removing and reinsert Batteries.
-
I think Batteriesplus also has individual Batteries, See if you can open pack without damage.
-
Try new Batteries, or removing and reinsert Batteries.
-
The WD 40 was not for lubrication, it was to release the junk then blow out. Brake Kleen would surely Remove all. Then use a DRY Lubricant, Would wipe a coating of WD on the face of the lock(The...
-
Just to mention, If they were wired in Series, All Bulbs would have too work, if one bulb was broke or removed, others would not light.
-
Spray down with WD 40 or something, wipe down, if it operates fine, keep it. Better than being dry. May not have wanted the Bright Brass to Tarnish.
-
I would check Fluid, and change Tranny Filter, Can't hurt, and may show little or lot of metal flakes.
-
The old way was to just take a hammer and break out the block behind it. If on a web, you can move over a little so it falls within a cell. Better is to take a Die grinder and cut out for the boxes,...
-
2 Common ways is T&M(time and materials), Not to be confused with T&A.
I charge my Hourly and add 20% to Materials. I give Customer the option to buy the Materials, Need to get paid for my Time....
-
What did you find with Fuel Pump, and Regulator?
-
Some have Throttle slides with 1 cable, some have 2 cables, a pull and a push cable. Be sure routing does not affect Throttle Operation while turning handlebars.
Can you describe more what you have?...
-
If You have no Manual, and you are cranking Engine during test, 2 things you could do, Hook a wire to fuel Pump wire at fuel pump, add test light, when you jump the relay, or provide power in relay...
-
Certified doesn't always mean Competent or Qualified. Change the Board and see if that is it? We call them Board Changers. I would do some testing before Buying a Board, Many are quick and Cheap...
|