Search:
Type: Posts; User: parttime
Search:
Search took 0.02 seconds.
-
https://en.wikipedia.org/wiki/List_of_United_States_federal_executive_orders
Scott?
-
Excon, I'm afraid you might be right.
-
Newt, says exempt Trump from ethics laws. That's the way dictators are made is it not?
...
-
This was posted by a long time plumber on this site. Good luck
If you do not flush,(not drain) your heater on a regular basis it will build up mineral on the bottom of the tank. When the flame...
-
-
Hi miksicht, if you give more info you may get an answer that will solve your problem. Make, model will help.
-
That's a faucet spray diverter, take the old one to supply store and match it up.
-
Good point Mike45plus, check for correct placement of refill tube while the lid is off.
-
Hi Bob, Stanfortyman posted this a few years ago, Motor Connection Diagrams
Maybe it will help you. Good luck
-
Hi IHpower and welcome, Try here:
Nordyne / Intertherm Brand Parts and Accessories
-
Sounds to me like an air leak, will it run long enough to spray some carb cleaner around the outside of the carb to help locate a leak?
-
And the art work is fantastic Harold.
-
Hi Adam, more than likely one of the build in safeties are shut off the flame. If you post more information, make and model, you should get a better answer. Good luck
-
I don't know what other picture you will find. Good luck.
TRANSMISSION Diagram & Parts List for Model 917297040 Craftsman-Parts Tiller-Parts | SearsPartsDirect
-
Yeah right! You selling ocean front property in az. Also? Lol
-
http://enora.nordyne.com/Literature/710381a.pdf
This might help.
http://www.nortekhvac.com/literature/359a.pdf
this covers your model.
-
Hey Grady, good to see you back.
-
Hi abc and welcome, this wouldn't happen to be a three wire pressure switch would it?
-
Hi SSTRIFE and welcome, you'll have a better answer if you give more information. Make and model of furnace and what switch are you flipping?
-
Well that's a new one on me, good luck and be safe.
-
Hi again Don, have you watched as the furnace does a cycle and shuts down? How long does the fan run after the burners quit? Can you post a picture?
-
Hi Don and welcome, sounds like your furnace is over-heating, has the filter been changed? Vents all open? Duct work in good shape?
-
Hi Norplan, myself I'd use this flush cut blade in my jigsaw. Good luck
http://www.amazon.com/DEWALT-DW3311-Flush-Cut-Blade/dp/B000R8GVMG
-
Hi Rick and welcome, count the flashing red light and read the code. Just guessing I would suspect dirty filter and bad limit switch. Let us know how many flashes. Good luck
-
Thanks for the update, I'm glad you're warm again.
-
Thanks Riles, update will surely help someone else down the line.
-
Yeah, that shouldn't keep the ignitor from getting hot, only shut it off quick.
-
Riles you can test the rollout switch using your meter, test for continuity.
-
Hi again Riles, the pictures didn't do much for me and my old eyesight, sorry. Maybe someone else can make more of it.
-
Riles can you post a picture, does one of the panels have a schematic?
-
Rile, did you block the door switch when you did the test?
-
Hi again Riles, yes there is a procedure for checking the pressure switch, but it involves special tools that are rather expensive. If it was mine and I was sure the inducer fan was blowing strong...
-
Hi Riles and welcome, the fan you hear running is the inducer fan, it should start and activate a pressure switch. Do you have good airflow outside at the exhaust? Make sure the pipe is clear. ...
-
Hi Jake, if it was mine I would start at the battery connections and unhook and really clean every electrical connection I could, including all grounds, trying it each time I cleaned and...
-
Hi Jvertner and welcome, have you tried unplugging it for 10 minutes?
-
-
Hi frabarb, try cleaning the gasket good and putting a thin film of vaseline on it. That should do you.
-
Hey tickle, here it shows creativegoth as the op, is that not the case?
-
The idiots with values are infinitely more dangerous than the few with guns.
-
I use this site, seems to work for me.
White Pages | People Finder - AnyWho
-
47742 test
hey that works!! Thanks Mark.
-
Milo is dead on then, snake away and good luck.
-
Can you post a picture? Sure would help.
-
You never said if you're on city sewer or septic tank?
You never said if you're on city sewer or septic tank?
-
47684aliseaodo, are you on city sewer or septic tank? If snaking the line don't solve the problem, try a fitting like this at the washer stand pipe. Good luck
-
Your welcome, ask all you "new homeowner" questions here and get plenty of expert advice. Good luck.
-
Hi theresamj and welcome, yes inch it up until it's where you want it, it wouldn't hurt to flush the water heater since its new to you.
-
47669
If you click hub (top circle) then click import favorites in 10's browser it should work. It did for me at least.
-
There is an "import favorites" that worked great for me. Not sure where it was, I remember it in the top right hand corner of the page. Plenty of tutorials also.
-
Your welcome, come back with any question or jump in and answer questions to help out.
|