Search:
Type: Posts; User: greghvacguy
Search:
Search took 0.00 seconds.
-
I would also look in to zoning the basement from the house so you can adjust the temp in the basement.
-
If the sound is in the wall what is in the wall heating vents.flue pipe,pluming. If it heating ducks then wall will need to be open to fix.the ducks are to tight to wall and making noise.
-
Hvac 1000 there is a post on here to fix your snow blower. No snow here today but lots still on the ground it will be 50 this weekend..
-
Sorry to hear that you are dealing with this. Yes you nees someone who knows how to ake care of the boiler.Next I would not pay him his rent till your warm.when he ask you where his check is tell him...
-
That was the part the fireplace manufactor sent us.I called them gave m# ans s# and they sent out the power pile and fast action thermocouple(fir I will change thermocouple since I was pulling pilot...
-
It may not be a bad thing to put a new furnace is as to it being 20 years old.New furnace will save you in gas and electric. If you go with a 90+ viribale speed motor. With the right install and...
-
I just worked on one. Unit would work when turned on the millvolts was 200ish when box got hot 10 min. the unit would shut down millvolts dropped down to 150. Moved wires around aand would go back up...
-
Sorry not shure if rheem has or had them on the inducer.I should have said check and see if you need one.I know Heil has them and have to take them off the old inducer.I have been out on calls where...
-
Sorry Just one more thing is there a humidifer or air cleaner hooked up to the furnace if so diconect any wires that go to the furnace.There mite be a back feed from one of them.
-
WOW.. I have seen this before. Found it to be 24volts reversed. Try and run a new ground wire from furnace to a copper pipe. Just a thought.Check all wires they mite be pinched some where.Look(pull...
-
Sounds like the duct work is not sized right to get the air to the 2nd floor. Is there dampers in the duct work they can be closed? Is this a new home?Did this just started?you may need to zone the...
-
We can only help if you go to your furnace and see what gos to what let us know so we can help
-
Pull the blower housing out. Take blower wheel nut off,take the three or four bolts off motor bracket,then take the bolt off the band then put new motor in
-
Don't no what your asking. Pilot may need to be cleaned or thermocouple. If this does not take care of it may need new gas vaule.
Post some pic then we can help.
-
On the reem inducer there should have been a restrictor plate on the back where the inducer goes to the heatexchanger (I think this furance had one)
The amps should be below .75
Still sounds like...
-
Need more info. Furnace model and make.
Info on old moudel what wire went to what and where did you put them to new one.what s8610u**** did you get.
-
Wire it to high speed do not hook up low speed.
-
If your getting a glow you should be getting gas to the pilot. If not check to see if your pilot need to be cleaned. On your gas vaule does the wires come in to top or is one on the side. If you have...
-
You need to clean cross lighter for the burners. If all the burners don't light then it will drop out.
-
As KC said that a 90% furnace is draining water from the burners. I would look in to bring in fresh air to furnace room(only if your furnace is not a two pipe PVC).Next try to winter rise your home...
-
Inducer are not made by Carrier,byant,panyne,daynight,trane,york,heil,lennox and so on. They are made by only a few manufactors. They make them out of plastic because if they where out of metal they...
-
Sounds like you need to clean flame sensor.on left side in front of burner. Pull it out sand it off with sand papper the wire brush put back in let us know if it works
-
IT could be the cat in the blower LOL sorry had to
-
-
My hat is off to you HVAC post 13. I always look for your input on the post. I have been in the bis for 14 years. I allway do the job the right way (the way I know.mite not be right way but the best...
-
Not sure on that unit but you need to find out if the unit controls the fan in heating. If not you need to set your t-stat to turn fan on when a call for heat. Depends on your t stat how you set...
-
Sounds like the flame sensor needs to be cleaned. It on the left side.(other side from his the thing glowing red) Its in front of the buner clean it with sand papper the wire brush.
For the ac...
-
High temp rtv. But first make sure this is not for freash air if you can take pic. That would help us
-
Make sure you have good ground.
-
Red to rh keep the jumper to rc
White to w
Yellow to y
Green to g
Drop the blue or put it to c or b
-
That is cool you have all the pic we need how long did it take you to get them all
-
Sounds like too much water your trap is the white thing at the bottom of you pic. It hangs down into the blower compartment. Take it off and clean it out with water. And the hose coming off that...
-
Clean your flame sensor. If you can't find it take a pic and post will try to locate it for you
-
Call you HVAC man!! After you turn it off and leave the house...
-
It can feeding water all the time. After you get boiler back to 12-15 check and see if the water keeps feeding if so need new valve
-
Don't know much on the settings on that. Not big fan of the ritetemp. Go for a honeywell vison pro or fouse pro. Whiterodges makes a good state to
-
There is no flame sensor on this furnace. It is done by the HSI. Check the omhs on it if over 80 put new one in. Check the heatexchanger they go bad seen a lot. If this is on propane stop using it...
-
Need to know more of the t-state.sounds like you need to set the cycle rate on the state or set it for forced air
-
We need more info make, model, and what it is doing as much as you can tell us
-
Rh 24 volts for heat and rc 24 volts for ac.keep them jumped. The old t state is a 2 stage heat the new one is not if your furnace is 2 stage then you need new t stat that does 2 stage.check your...
-
Some furnace have fuse what is make and model. Check braker box.some switch to furnace have fuse. On the capacitor has two spots one wire to each.
-
Try the braker of fuse sounds like you blew it
-
What about the old on. Sounds like you have the wrong t stat
-
No if you do that 2nd stage on your furnace will run all the time when your thermstate calls for heat. Sounds like your new stat is for 1 stage of heat not 2. is your furnace 2 stage or one. On your...
-
Working on a york rtu m#d8cg060n09925a. The call came in that fan stays on. Could not get unit to do it so the main control board was replased. Week latter they called again this time I went out and...
|