Search:
Type: Posts; User: mr500
Search:
Search took 0.01 seconds.
-
Anonymous Call Rejection
Anonymous call rejection - Wikipedia, the free encyclopedia
*77 and they won't bother you again. Read the article.
-
Things you can find when you Google! :)
Motorola MD481 User manual Download
MD480 series manualzzzzzzzzzzzzzzzz
-
Ok sounds good.
I live in a newer triple wide and my vents are in the walls seems like and run straight out through the roof.
But with his roof I see nothing.
-
Only thing is I do not see anything vented through the roof of his mobile home. Could it be vented in other ways in this trailer? I looked at the drain, both of them. They seem to be in the correct...
-
OK problem is, my dad in-law has a mobile home and neither of the toilets will flush out. He recently bought it and had it moved hence this is when the problem started. The toilets have not flushed...
-
If you turn off the faucets in the house, and the pump kicks on then the tank is the only place for the water to back up too. If it is not going into the tanks at all, then yes you could have a...
-
Don't go to parties at your house!! That's a riot. :eek:
-
Bad joint? Well least you have light. Most important patr! hahah
-
Well hope he can figure it out. Doesn't make much sense to me. Post back, Like to know what it is he found out about this one..
Mike
-
Humm I would think if you have power at the light in the ceiling, then it can only be the fixture or the wiring is wrong. BUT, like you said you only have the 3 most common wires in a circuit. Maybe,...
-
Just one small thing. 1. Has this light ever worked? 2. Check voltage at the wires coming out of the ceiling at the light itself. If the light has never worked for you, this switch might not even go...
-
Sounds like the motor is shot. The blinking light is problaby some type of error code or something. Look in the manual or go online with the model number and checkit out. OR call Sears and ask.
-
Step 1. Call licensed electrician. :) Are you planning on making this a DIY project>? OR are you curious to know what all happens? Or a test question?
-
-
Follow this post. Should be a model number on it somewhere. Look for some sort of decal
https://www.askmehelpdesk.com/electrical-lighting/directions-noma-timer-278919.html#post1366790
-
Another option, Ask around for a reputable repair shop, call them and have it towed in for a look see. Be a lot cheaper than the dealer.
Mike
-
-
Well how far are you needing to run the wire>? Is the garage attached to the house or freestanding?I recently finished the same project, and I used #2 for my run. Depending on if it is attached, You...
-
If you have a 2007 take it back to the dealer. Your should not need coolant with this being so new of a vehicle. I'm sure it has a waranty. Who told you that you needed to add coolant? Is it leaking?...
-
How far are you installing the 3rd set from the others? Can you not just tap into one of the other lights and run to the 3rd set of lights? That way you can keep everything as it is.
-
You cant. In order to change the load on a breaker coming from the house, you have to re wire that circuit and then add a breaker. For instance, you can't break up the living room plugs just by...
-
It was tired and went on Welfare!!
-
GFI GFI GFI.. I personally don't see any reason to use the breaker, I would just use a gfi outlet for this app. If water puddles up next to the house I would raise the location of course. I would run...
-
OK I turned on the fan, then the heat and damn the heat stayed on.
I noticed too that the fan alone blows a lot harder than when I turn on just the heat/fan.
So I guess what's my next step....
-
I don't have the optional relay on the fan. Just the one round capacitor as far as I know. I will try the fan on, then turn on heat and see what that does. Now, if the heat works what would my next...
-
Maybe you guys can help me. My heater will come on for about a minute or so, then kick off for about 30seconds and repeats this cycle. I have replaced the 2 contacts as I was told that might be the...
-
Yes you need a sub panel. And a few other things as well. You are only wanting to run 30 amps? Nothing is wrong with that, but in future your demand might outweigh the 30 amps. BUT, if you don't...
-
-
Im not sure how small these screws are, but I have used Vaseline on the tip of the screw driver. Kind of holds the screws.
You can also magnetize the tip of your screwdriver... :D
-
240 Volt uses half the amperage that 120 Volt uses, therefore it's more efficient than 120 Volt. You get more bang for your buck with 240Volt compared to 120
Just my 2 cents. As in motors for...
-
Do you have a jump/flash drive that you can use via the USB port? Copy all onto that and transfer them to the other PC. Done Deal!
-
If it is a new install, as far as colors I don't see where it would matter. Just as long as they are connected to the correct terminals.
How many pairs of wires are in the sheathing? Ive never...
-
Have you by chanced tripped a breaker? That would throw a wrench in your operation.
Just something to check.
-
If this is a 2 3-way switch set up, the red is a traveler from one switch to the other.
Did you take notes on how the fan was wired before you took it down?>
-
NP Im at work anyway. I had the time ahahaha Have a good one!!
:D :D :D :D :D :D
-
Again might out of slap a few turns of l black tape on orange wire to show it is hott... On both ends
-
Yeah as we went along I got a better understanding of what u had. The damn orange threw me off. Must have used that 3 conducter wire just to confuse us.
Usually it's a blk hot to bottom screw, a...
-
I don't know either. Was hoping one of the gurus would chime in on this...
So, the bottom screw has a hot blk going to it now? On the switch?
We only need to get 1 hot on that switch and then...
-
Yeah where was the exrea blk in your box going too?? Was it capped with all the other blk hot wires?
Might outa take sum blk tape and run it around the ends of the orange to show that it is hott...
-
One more thing. The blk wire from the light is going where? Is it wire nutted with all the other blk wires? It shouldn't be. Actaully a blk should feed the bottom switch screw, another blk coming off...
-
OK so it has never had a switch in this box right? IF so, try this, the blk wire at the switch box is on the bottom and the orange is on the top...
This should be hot feed to your light. Have...
-
OK gotcha. What was this switch used of for before you installed the new lights? Orange has got me confused somewhat... lol.
-
So coming out of the light is blk and white, yet in the switch box there is not a blk and white is this correct? Rather that orange wire
-
Yeah, What color wires on the light is the ribbed and smooth wire connected too? Is it orange etc. or is it blk white?
-
Yeah take the load OFF the switch and try it ? See if it trips. If it still does it then it probably is not the light.
Just undo the light wiring and see what happens. Like you said then at least...
-
Yeah I photo shopped the first one as well lol. Ask a weird question, when this problem occurs, is the switch IN the box or OUT. Have you tried it both ways?
Looks like you have it wired...
-
NO not seperatly per say. Wire the gfi with the INCOMING power feed into the LINE side of the gfi. Black to brass and white to silver.Pig tail the green/bare ground and run it into the green screw....
-
OK. And you want to install 2 outlets in the box correct? And you have a total of 2 romex wires coming into the box, as I read. Do you have the gfi bought? You only need one. And a new outlet if you...
-
So you have 3 switches problaby controlled by the same hot wire. How many wires are connected to your problem switch?>
You say there are only 2 whites feeding into the box?
-
OK. When I say downstream I mean on the other side of the gfi. Your power comes in from the panel to the gfi first. Then anything after that is "downstream".
Is this a 2 gang box? Is the box big...
|