Ask Experts Questions for FREE Help !
Ask
    mooney10's Avatar
    mooney10 Posts: 6, Reputation: 1
    New Member
     
    #1

    Apr 2, 2008, 05:25 PM
    Two P traps on one pipe?
    I'm installing a shower in the basement in an older house, it has a p trap about 3 feet strait down under the shower! Should I put a p trap directly under the shower? Or would this cause burping with 2 p traps in the line?
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #2

    Apr 2, 2008, 05:39 PM
    Hi Mooney:

    Hey... 3 feet is pushing it... BUT... you cannot connect any drain using 2 ptraps... no exceptions to this! So stick with what you have at this point and connect riser to shower drain. Is drain off center of shower... or directly under?

    What kind of shower? Describe as much as you can. Is there a pre-molded shower floor... or a custom pan? Let me know... few tricks go with each type... Mark

    .
    mooney10's Avatar
    mooney10 Posts: 6, Reputation: 1
    New Member
     
    #3

    Apr 2, 2008, 06:07 PM
    Thanks for the Quick Answer, the Drain is off center about 12", The Pan is A Kohler fiberglass 36X60 so had to move the drain 12" it was originally set up for a 36x36 . It is a cast iron riser.
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #4

    Apr 2, 2008, 06:19 PM
    Mooney:

    Unless you want to dig down three feet, you want to dig down a foot or so... cut the cast iron riser (will not be easy...talk to me about this if going to do it yourself).. and OFFSET the drain using PVC pipe and (2) 45 degree fittings into the new pvc drain assembly of the fiberglass pan. Use a 2" PVC x 2" cast iron shielded coupling (code approved) to make the transition between 2" cast iron and 2" PVC pipe (available at all plumbing supply houses).

    Also want to set that fiberglass shower pan into a bed of perlited gypsum structolite mortar or a modified thinset mortar bed to reduce sqeeeks/motion at pan. Also, talk to me if planning to do yourself.

    Let me know what you think... Mark

    .
    Attached Images
     
    mooney10's Avatar
    mooney10 Posts: 6, Reputation: 1
    New Member
     
    #5

    Apr 2, 2008, 06:38 PM
    I already cut the pipe and have the shielded coupling, but I bought 2 90s should I go with the 45s? Also I plan to set the pan myself.
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #6

    Apr 2, 2008, 06:43 PM
    Yes... you need to purchase (2) 45s. Code frowns on 90s... ;)

    If planning pan... check out this site:

    How to Build a Shower Pan

    Get back to us if need more... Mark

    .
    mooney10's Avatar
    mooney10 Posts: 6, Reputation: 1
    New Member
     
    #7

    Apr 2, 2008, 06:47 PM
    Thank you for all of your help! You have been Great source of Information! Thanks again.

    I will follow all of your advice
    mooney10's Avatar
    mooney10 Posts: 6, Reputation: 1
    New Member
     
    #8

    Apr 2, 2008, 06:59 PM
    Mark
    I'm going to set the fiberglass pan myself, so I should set it in a base of thinset morter,how thick shoul it be?
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #9

    Apr 2, 2008, 07:20 PM
    Hey Mooney:

    Look at shower base... will see outer perimeter and base itself. At base, want between 2-4 inches of MODIFIED thinset mortar (sold in buckets at home supply) or structolite, and then push down tight to floor so that base is level from front to back and from side to side (dry fit this... i.e. practice this.. then when understand floor, base, and corners of walls... set in mortar for best result). Look at base... add 1 inch more than you think you need... then let dry overnight before stepping into/on shower floor... that should do it.

    Let us know what you think... anytime... Mark

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

P traps [ 1 Answers ]

How do I install a p trap on my sink, shower/tub?

S traps [ 2 Answers ]

I live in Minnesota and am trying to find when S traps were determined to be "illegal". Also, what is the problem with them? Thank you very much for this forum!

''S'' Traps [ 2 Answers ]

Tom, if you hadn't educated me on vents and traps, I might never notice a bunch of stuff. Recently I spent 2 days in the basement of the dog guide school kennel in a training session. Largely unfinished, likely never intended to have 75 dogs and their people there all day for training. At one...

Water htr/heat traps/pipe config. [ 2 Answers ]

Some time back I installed a new water heater and it had the factory installed heat traps. The instructions say you MAY have to install one or more 90° elbows in order to make a “U” configuration in the supply pipes. It also shows the pipes running vertically from the heater. I’ve read on various...

Is having 2 traps OK? [ 5 Answers ]

Hello, I have moved my washer and dryer and added a sink for a 1/2 bath in that spot. The washer had an existing trap in the wall. It would be a real pain to cut it out because it is galvanized pipe and because of were the trap is located. Would it be OK to leave the existing trap in the...


View more questions Search