Ask Experts Questions for FREE Help !
Ask
    jmcd's Avatar
    jmcd Posts: 2, Reputation: 1
    New Member
     
    #1

    May 23, 2008, 12:27 PM
    Standard toilet rough in
    We have hit a snag in our bathroom remodel. Our contractor installed the flange at the standard 12" wall to center of flange distance, but an installed toilet sits 2-3" from the wall. We have had 3 different toilets in the room to try to figure out what is going on. They are all "standard" toilets (Kohler/American Standard brands), but they do not fit properly. We finally found a toilet that actually measures 12" from the center of the hole to the back of the tank but it was an older, cheaper, discontinued model. We are wondering if the manufacturers have redesigned newer toilets to sit further from the wall? Anybody have an explanation? The contractor and 2 home improvement stores are stumped.
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #2

    May 23, 2008, 12:31 PM
    Hey Jmcd:

    Nope.. I have been noticing this same trend of being farther from the wall then they used to be.

    Especially TOTO and some American standard toilets.

    All I can recommend is for you to go to a SHOWROOM and measure the 12" rough toilets in place against the wall...there will be some that work right. OR...

    check out a 14" rough toilet of the same toilets that have been short for 12"... maybe one of these will also be short on 14 and maybe.. just maybe will work for you.

    Otherwise, you are kind of stuck with this... and we as plumbers have to start getting better specification sheets from our manufacturers!

    Hope that helped some... MARK

    .
    jmcd's Avatar
    jmcd Posts: 2, Reputation: 1
    New Member
     
    #3

    May 23, 2008, 01:18 PM
    Quote Originally Posted by massplumber2008
    Hey Jmcd:

    Nope..I have been noticing this same trend of being farther from the wall then they used to be.

    Especially TOTO and some American standard toilets.

    All I can recommend is for you to go to a SHOWROOM and measure the 12" rough toilets in place against the wall...there will be some that work right. OR...

    check out a 14" rough toilet of the same toilets that have been short for 12"....maybe one of these will also be short on 14 and maybe ..just maybe will work for you.

    Otherwise, you are kinda stuck with this...and we as plumbers have to start getting better specification sheets from our manufacturers!!

    Hope that helped some...MARK

    .
    Well, it doesn't change the situation... but at least I have confirmation that we are not crazy as has been implied by some staff at unnamed home improvement stores! Thanks for the reply.
    truck 41's Avatar
    truck 41 Posts: 221, Reputation: 21
    Full Member
     
    #4

    May 24, 2008, 08:30 AM
    Hello jmcd,

    I would double check and make sure that the toilet or the tank isn't made for a 10" roughin.
    theres been a few times that I have received a toilet or tank for a 10" rough, instead of the standard 12" rough. Good luck

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Standard Rough in dimensions for bathrooms [ 20 Answers ]

We have a new home (Built 2 years ago) with an unfinished basement that I have begun finishing. The rough in for a full bath is already in place and consists of 2 in. pipe with vent through to roof for sink/vanity 4 in pipe for toilet Two inch pipe for tub (need dimensions both from side wall...

Toilet rough in [ 9 Answers ]

I live in a old house. The original rough in is 14 inches. I am finding it is very hard to find a toilet to meet the new space I have for a toilet. Can I replace a 14 inch rough in toilet with a 12 inch rough in without changing any plumbing? Thank you for the response back.

Standard or oversize toilet wax ring [ 1 Answers ]

How do I determine whether I need a standard toilet wax ring versus the thicker wax ring? Is there a gap distance that would suggest one over the other. I installed tile and now have a 1/2 inch gap between the flange surface and the floor (tile) surface.

Bouncing flapper American Standard toilet [ 3 Answers ]

I have an American Standard one-piece low boy elongated toilet that was installed originally in 1956. About 6 months ago I replaced the flapper. It bounced a little so I glued a penney to it and until recently it has worked fine. Now it bounces ( rapidly ) and keeps the water running as it won't...

American Standard Plebe toilet tank [ 1 Answers ]

Getting old I guess, anyone know the tank to bowl bolt spread on a American Standard Plebe (the old ones), can't remember if 51/4 or 51/2 inches.


View more questions Search