|
|
|
|
New Member
|
|
Oct 25, 2007, 07:48 AM
|
|
Replacement for copper toilet flange
Next step in my bathroom remodel is getting the floors up and new floors down. I have a 3" copper toilet drain with a copper flange soldered to it. I know I can use a torch to get the flange off.
But, what should I replace it with when I get my new floor in. I am having a hard time locating copper closet flanges and it may be a bit hard for me to solder it in there after the floor was installed.
Can I use something like the Oatey Twist-n-set? Any other recommendations on a flange to go into 3" copper? I'm a little worried about controlling the height of a twist-n-set so it willsit on my new floor.
Thanks,
Steve
|
|
|
New Member
|
|
May 25, 2010, 06:49 PM
|
|
Hi Steve:
I am also in your position just that I have a coppey "Y" and couple of elbows goes for approx 22.5 inch (may be more) going to the top. I found that the last owner put PVC flange on top of it (which is absolutely wrong). And the joint between copper and PVC was leaking.
I have something similar to what you have just that couldn't find copper flange so thinking of putting a copper pipe and using fernco coupling from copper pipe to PVC to pvc flenge but this total hight of this setup is high.
Got someestimates and "master" plumbers suggested removing copper "Y" with PVC pipe by cutting copper. They gave quotes of around $1200 for this and that seems way high. I am looking for a less invasive approach.
So just curious what did you endup doing? Your help/answer is highly appreciated.
|
|
|
Senior Plumbing Expert
|
|
May 26, 2010, 05:40 AM
|
|
Hi Tired...
The post you jumped into is from 2007 so I'm confident that Ultralight may not return... especially since he doesn't appear to have gotten an answer to his original question... ;)
I'm off and running to work, but when I get back in I will look this question up again and post an answer... look for it later today.
Mark
|
|
|
New Member
|
|
May 26, 2010, 11:53 AM
|
|
Thanks Mark. Actually the total height from the first elbow to the floor is only 5.5 to 6 inches. Where as the total propose set up height is around 22 inches.
Do they make flange that can connect directly to Fernco coupling and is it legal? What do other people do when they have copper pipe and couple of elbows up to the floor? How do the people did such things 40 year back (thats when when the house was built)? So many questions but whatever you can answer would be highly appreciated... Just moved in so can't afford money equal to my monthly mortgage... Thanks for your help...
|
|
|
Senior Plumbing Expert
|
|
May 27, 2010, 04:52 AM
|
|
To make this all legal, you can't use the all rubber fernco couplings... you'll need to purchase a copper x PVC plastic shielded mission (or proflex) transition clamp... see image.
40 years ago... they simply installed more copper pipe and fittings... ;)
Since height is an issue you should be able to use street fittings (hubless on one end). For example, you could cut the copper, install the shielded mission clamp and then install a 4"x3" STREET closet flange directly into the shielded clamp. With any luck that will work for you. Keep me posted... O.K?
Mark
|
|
|
New Member
|
|
May 27, 2010, 05:05 AM
|
|
Hi Mark:
Thanks for the update.
Yes, I have similar metal shielded copper to pvc coupling. My question is, since I do not have too much height to use the street coupling, can I put the flange into the copper to pvc connector directly?
Am I missing something here?
Thanks a ton for your help.
I will let you know.
|
|
|
Senior Plumbing Expert
|
|
May 27, 2010, 05:40 AM
|
|
As long as that clamp is an approved shielded transition clamp then you sure as heck can.
|
|
|
New Member
|
|
May 27, 2010, 09:23 AM
|
|
Thanks Mike. I really appreciate your help.
|
|
|
Senior Plumbing Expert
|
|
May 27, 2010, 10:08 AM
|
|
Glad to help!
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Shower base gone, now how to get this copper flange off?
[ 4 Answers ]
Thanks to Ballengerb1 and Tom for answering my question about getting the shower concrete/stone aggregate shower pan out. I hit it a little harder and it shattered just fine.
The shower pan is removed and I am left with the copper drain pipe and some type of flange stuck on the outside. I...
Flange replacement
[ 3 Answers ]
What type of adhesive should be used to replace a flange around a shower supply pipe when the flange will not simply snap and lock into place. The shower wall is covered with white 4 inch ceramic tiles?
Replacement drain for 2" copper raiser
[ 1 Answers ]
Ok,
I have tile person coming to pour the new shower pan and tile mysoon to be new shower. All I have left to do is put in a new shower drain. The shower drains through a 2 inch copper pipe. The old brass or iron drain was welded ( I guess) on to the pipe. I knocked the heck out of it with a...
PVC toilet mount and flange replacement on slab
[ 3 Answers ]
Hi.
I'm a new home owner and an idiot. I discovered that our toilet on the first floor (no basement) was rocking back and forth, and upon attempting to tighten down bolts, further discovered that they spun freely. I removed the toilet to find that both slots of the pvc mount were broken. ...
View more questions
Search
|