Ask Experts Questions for FREE Help !
Ask
    majake01's Avatar
    majake01 Posts: 4, Reputation: 1
    New Member
    		  
    #1

    Nov 30, 2011, 01:27 PM
    New washing machine-standpipe overflow
    Old Maytag finally gave up the ghost so I went and purchased a shiny new HE GE washing machine for my wife. The wife was very happy. I installed new shiny mahine and gave wife a new bottle of HE detergent and said "Merry Christmas" Wife did not think that was funny and now not as happy. Wife ran a load and called me and said " there is water shooting out of the pipe thing behind the washer I asked her to please turn off the washer. Wife is now very unhappy.
    I was scouting here yaesterday and I believe my problem might be that the standpipe is 1.5 inches diameter and only 20" above the trap.

    Here's a pic if it helps


    There is a cabinet 24" above the top of the pipe so extending it is possible. Any suggestions short of buying a new house (wife's suggestion) would be appreciated.
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
    		  
    #2

    Nov 30, 2011, 01:55 PM
    I believe my problem might be that the standpipe is 1.5 inches diameter and only 20" above the trap.
    And you'd be correct. Sadly , unless you want to tear up stuff and increase the size of the pipe there isn't anything to increase the trap and under floor pipes. But we can add a coupling and a piece of PVC to make the stand pipe at least 36" from the trap. to the standpipe.
    However, because todays washers have more powerful pumps and discharge with great volicity and volume you may still have back ups.
    I have a older home with the same washer setup as you. When my new washer began to back up I Installed a 1 1/2" PVC compression adapter on the end of the stand pipe and made it a closed system forcing the discharge down the drain. Duct tape works also. This won't hurt the washer and you'll be back up free. It's been three years without a backup for me. This is a cheap fix that should bring a smile back to your wife's face. Good luck, Tom
    Attached Images
     
    majake01's Avatar
    majake01 Posts: 4, Reputation: 1
    New Member
    		  
    #3

    Nov 30, 2011, 02:09 PM
    Thanks Speedball

    That sounds like a cheap and easy fix. I think I'll try it. Should I be concerned about siphoning if there is no air gap?
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
    		  
    #4

    Nov 30, 2011, 02:16 PM
    Should I be concerned about siphoning if there is no air gap?
    Not if you make the stand pipe higher then the flood rim of the washer. There are a few things that we have recommended in the past that we have never got a complaint on. One is a high loop air gap for a dishwasher and the other is closing off the washer stand pipe to make a closed system. Cheers, Tom PS. Is your wife smiling yet?
    majake01's Avatar
    majake01 Posts: 4, Reputation: 1
    New Member
    		  
    #5

    Nov 30, 2011, 03:17 PM
    Hopefully I can rig this up tonight after work and get her smiling again. She's still a little miffed about the "Merry Christmas" joke. I'm afraid that's going to cost me. If it doen't work I'll be back to pick your brain again. Thanks again!
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
    		  
    #6

    Nov 30, 2011, 03:39 PM
    As I've stated. Duct Tape works also. I Duct Taped mine years ago and no backups as yet. Tom
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
    		  
    #7

    Dec 1, 2011, 07:18 AM
    In all the years that we'v recommended We have never had a complaint that it didn't work.
    Good luck, Tom
    majake01's Avatar
    majake01 Posts: 4, Reputation: 1
    New Member
    		  
    #8

    Dec 6, 2011, 10:57 AM
    I have called a few plumbers who wanted to do everything from run cameras down my pipes to completely replacing my drain lines.I finally gave up trying to fix this with chewing gum and duct tape and ordered a GVII valve from Jirasek systems. It came yesterday and I installed it last night in about five minutes. That thing works like a champ. No leaks at all!
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
    		  
    #9

    Dec 6, 2011, 01:50 PM
    Great! You did exactly as I suggested and made it a closed system. Glade you're all fixed up. Tom
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Washing machine discharge, standpipe [ 14 Answers ]

Last week our washing machine drain overflowed. The plumber tried to snake it out, but the problem only became worse (i.e. no flow at all any more). He opened up the drywall and discovered a very corroded cast iron pipe going horizontally from the standpipe via a trap to a T at a vertical pipe...

Washing Machine Standpipe Height [ 1 Answers ]

I am installing a washing machine in the basement and the sewage drain pipe is at a height of 5 feet off the floor. From everything I have read, the standpipe should be above the height of the washer tub and it should be 2" in diameter. Could I install the washer without having a external pump...

Washing machine standpipe overflow [ 2 Answers ]

I just recently had my washing machine overflow from the standpipe. I have never had an issue with this until the other day. It overflows initially when the washing machine begins to drain. Once the intital draining slows down it does not overflow anymore. The standpipe is approx. 30" high and...

Laundry standpipe drain overflow - washing machine washer [ 12 Answers ]

I have a Kenmore He3T washer that has worked fine for just over a year. It came with a new drain hose with a 'hard U' for hooking on the standpipe and has had no problems up to this point. For the first time, I accidentally used standard soap (non HE) for about a dozen loads. This is when the...

New washing machine discharge standpipe [ 9 Answers ]

Hi, I'm putting in a new washing machine tomorrow, and would like to ask how much higher should the standpipe be? I am including a link with 2 pictures of how it is presently.(I have moved the electrical receptacle). In the picture, the distance from the top of the standpipe to the bottom of the...

View more questions Search