 |
|
|
 |
New Member
|
|
Oct 27, 2008, 07:48 PM
|
|
Low pressure in my kitchen sink ONLY
Hello,
I have an american standard two handle sink with side handsprayer. It is in the 'hamilton' collection.
American Standard - Products
In the past few weeks the water pressure has been abysmal. It is almost a joke. When we installed the sink a year ago, we also replaced the supply hoses to the sink as well as the valves - they are all new.
Now, when you turn the faucet on slightly, the pressure starts OK. It was never as good as my old ugly faucet, but I assumed it was just "different" than my old faucet, so I got used to it. As you continue to turn it on, the pressure drops. It doesn't matter if it is hot or cold.
I cleaned the aerator - the problem persists even without the aerator on. I also removed the main stem and got it down to this
I don't know what that little tabbed screw looking thing is, but when I push it down, no water comes out. I assume it is the divertor to the handsprayer? I also notice that it wants to 'pop up' as the water is turn on. Is this supposed to happen? When I put everything back together, it seemed to be fine for a few minutes, then the pressure was crap again.
Not sure what the problem is, but I do know that the website says "lifetime warranty". I'm worried they'll send me another faucet only for the same issue to arise.
|
|
 |
Ultra Member
|
|
Oct 27, 2008, 09:57 PM
|
|
It looks like it is time for a new faucet, before you do any thing call American Standerat at
1-800-442-1902, tell them about your problem they will tell you what to do, or they may send you a new faucet if you are lucky, thanks.
John
|
|
 |
Plumbing Expert
|
|
Oct 27, 2008, 10:36 PM
|
|
Clean your Aerator... Aerator is the filter screen on tip of your faucet spout.
|
|
 |
Ultra Member
|
|
Oct 27, 2008, 10:44 PM
|
|
Hi Milo,
I think he says that he removed the Aerator and the problem persists even without the aerator on, that's why I asked to contact the American Stander, Thanks..
John
|
|
 |
New Member
|
|
Oct 28, 2008, 06:42 AM
|
|
So, no clues as to what the screw thing in the pictures is?
I will call American standard definitely - no doubts there. I was just hoping someone had a little advice on something else I might be missing.
Oh, and by the way... I'm a girl. :)
|
|
 |
Plumbing Expert
|
|
Oct 28, 2008, 06:50 AM
|
|
1. See if your angle stops are open all the way.
2. In any case: Open and Close both angle stops.
3. Look under sink. There are h/c water supplies. Make sure they are not kinked.
Gender has nothing to do with it...
I don't know hat "screw" you are talking about. I looked your photos but don't see any screw. They only screw on the spout is the one that holds the spout to to the body. Can you be more specific ?
|
|
 |
New Member
|
|
Oct 28, 2008, 06:52 AM
|
|
In the picture, zoom in. There is a little magnifying glass thing you can click to zoom.
In the middle of the pipe, there is a small brown screw looking thing. It has four tabs that come off it. It looks like a regular flat head screwdriver would fit into it.
What are angle stops?
The hoses underneath are not kinked, and the shut off valves are fully opened.
|
|
 |
New Member
|
|
Oct 28, 2008, 06:54 AM
|
|
I said I was a girl, because afaroo kept calling me 'he'. I know gender has nothing to do with it...
:rolleyes:
|
|
 |
Plumbing Expert
|
|
Oct 28, 2008, 06:56 AM
|
|
OK, that thing is your diverter... Can you remove it ?
Also, try this: remove the diverter, put towel over the hole and turn water on. See if you get lots of pressure. Then, install the diverter, put towel over the hole again and see how much pressure you have now. This test should tell us whether it is the diverter that is the cause of your water flow problem.
|
|
 |
New Member
|
|
Oct 28, 2008, 06:59 AM
|
|
I tried removing the divertor last night. I gentry tried to coax it out, and nothing. Then I even grabbed it with pliers and tried slightly forcefully, but it doesn't come out. I'm afraid that if I REALLY try, I will break something important.
It almost seems like it is on a spring? It sort of goes up and down slightly (a quarter of an inch or so) but it won't come up to be removed. As the pressure underneath of it mounts, however (as I turn the valves on more) it seems to pop up slightly more than I wonder if it should. I wonder if that blocks the flow of water --- I'm not sure.
|
|
 |
Plumbing Expert
|
|
Oct 28, 2008, 07:22 AM
|
|
Yes, diverters can restrict water flow and frequently do. Also, you may have dirt accumulated below the diverter. It is common problem...
That up/down movement is what diverts water to the spout and hand spray. The diverter sits on one or two O-rings inside the faucet. It is very common that it is "frozen" in. Play with it, jiggle it side to side, twist it, and apply even, upward pull pressure. It should go...
Make sure your h/c water handles are in close position.
|
|
 |
New Member
|
|
Oct 28, 2008, 07:25 AM
|
|
Ok. I will try this again tonight and let you know the results.
I am also currently on hold with A.S. to complain!
|
|
 |
Ultra Member
|
|
Oct 28, 2008, 08:29 AM
|
|
 Originally Posted by stalkproof
I said I was a girl, because afaroo kept calling me 'he'. i know gender has nothing to do with it....
:rolleyes:
Dear Stalkproof,
I am sorry and Apologize by reading the post wouldn’t be able to tell who is who, Thanks.
Regards,
John
|
|
 |
Ultra Member
|
|
Oct 28, 2008, 08:33 AM
|
|
Please Fallow Milo's instruction before you call American Standard, good luck.
John
|
|
 |
New Member
|
|
Oct 28, 2008, 08:34 AM
|
|
No worries. I am appreciative of all of the advice. I do realize that by reading my username no one would be able tell who is who and what is what.
I'm not offended. Not at all.
I called A.S. today and they are sending me a new diverter and... new cartridges? I assume the cartridges go inside the handles. I now know what the diverter is, so I know where that should go. The question will be trying to get that thing out.
I will update with the results.
|
|
 |
Ultra Member
|
|
Oct 28, 2008, 08:45 AM
|
|
Very Good,
Ask A.S to send you the removel/installation instructions VIA email that will help you, good luck.
John
|
|
 |
Plumbing Expert
|
|
Oct 28, 2008, 02:29 PM
|
|
That's great. You will have all new interior parts for your new A.S. faucet. It should work like new after the parts are installed. You need only basic tools and bit of common sense to install them.
And hey, that: woman/man issue - you did lot better than many male posters on this site ! :cool:
Get back to us to let us know how you did...
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
No hot water pressure in kitchen sink
[ 11 Answers ]
Hi. I have an old kitchen faucet. I replaced the valve stem to the hot water side because it continually dripped. I had to get this part at the specialty store because it is so old. Anyway, I replaced that faucet was fine. Just the other day the hot water ended up having no pressure. I used it then...
Low pressure in kitchen sink
[ 6 Answers ]
I live in a basement apartment and i tried to fix a leaking shower and failed. But now the water pressure in my kitchen is low.
No pressure at kitchen sink
[ 1 Answers ]
We recently lost power to our house during a storm, since we live in the country we have a well and water pump system. While the power was out the kitchen sink faucet was turned on but no water came out because of no power to the water pump, a clunking noise was heard while the line was open...
Low Water Pressure in Kitchen Sink
[ 1 Answers ]
A few months ago, out of nowhere, the kitchen sink's hot water pressure became very low. A plummer came over and all he did was totally replace the faucet; nonetheless, the problem still exist so I doubt it's the washers or simply being clogged. I don't exactly trust this plummer; he's saying it...
No pressure in kitchen sink
[ 2 Answers ]
I recently had a new water heater installed. Since that occurred have very little water pressure in my kitchen sink now. Any ideas?
Thanks!
View more questions
Search
|